Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
a. A WLAN uses the 1-Mbps IEEE 802.11 infrared standard and the 16-PPM modulation scheme. Compute the period of transmission (time between bits).
b. What is the average time between pulses (1 values) and the corresponding average rate of pulse transmission?
c. Compute the minimum time between adjacent pulses
d. Compute the maximum time between adjacent pulses.
A 75 ohms lossless air transmission line at 3 GHz is terminated in a load of (300-j400) (a) What is the load reflection coecient (b) Determine the impedance at 2.5 cm, 5.0 cm, 7.5 cm and 10 cm from the load.
The purpose of this project is to design a device that would remotely control (from a Bluetooth-enabled mobile phone for instance) at least two actuators (e.g. relays and switches).
A police K-band radar is operating, with transmit power of 1000 Watts and antenna gain of 300 in linear units. The radar unit is designed to detect a target with a radar cross-section (RCS) of 6 sq. meters and its receiver can detect a signal
Despite the advantages to the synchronous alternator there is a downside and this has to do with keeping the load balanced on such a machine. Why is balancing the load so important to the synchronous alternator?
A purely inductive load of 10 ohms is connected to an ac source of 120 V (rms) through a half wave SCR circuit. a. If the SCR is triggered at 90 degrees, calculate the angle at the maximum instantaneous current.
An otherwise-ideal op amp, known to have an open loop gain of 10^4 V/V , is measured in a circuit to have an output voltage of -3 V. While it would be difficult to measure, what would you expect the voltage from the negative terminal
transfer function: T(s)=1/(0.1s+1) with all initail conditions at 0 a) if the input is 1.5sin(2t)*u(t) find the steady state value of the output b) after the input is applied, approximately how long will it take for the steady state value you found i..
Suppose that without a 1k-ohm load an amplifier's output voltage is 5Vpp but when the 1k-ohm load is attached, it drops to 3Vpp. What is the output impedance of the amplifier
A long hallway has three doors, one at each end and one in the middle. A switch is located at each door to operate the incandescent lights along the hallway. Label the switches A,B AND C. design a logic circuit network to control the lights.
The detector will take in numbers from 1510 to 010 encoded in binary labeled [N3:N0] with N3 being the most significant bit. The output will be asserted when the decimal value of the input is a prime number (i.e., 2,3,5,7,11,13). The output is de-..
Why can't a video signal such as an NTSC analog television signal be transmitted over a two km length of loaded twisted pair cable with a frequency range 300 Hz to 3,400 Hz? What is the bandwidth occupied by an NTSC video signal?
3-phase-Y-connected load of 40,000W at 0.8 PF lag is supplied by a three-phase Y-connected source of 500V. Find the current and phase voltages. Assuming Van as ref. Determine Ian, Ibn, Icn, Vab, Vbc, and Vca in phasor form.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd