Determine the value of p for which motion occurs

Assignment Help Civil Engineering
Reference no: EM13562601

Two 8-kg blocks A and B resting on shelves are connected by a rod of negligible mass. Knowing that the magnitude of a horizontal force P applied at C is slowly increased from zero, determine the value of P for which motion occurs, and what that motion is, when the coefficient of static friction between all surfaces is (a) ?s = 0.40, (b) ?s = 0.50.

Reference no: EM13562601

Questions Cloud

Determine the aeration period : Two activated sludge aeration tanks in Podunk, MO are operated in series. Each tank has the follwing dimensions: 7.0 m wide x 28.0 m long x 3.5 m effective liquid depth. The plant operating parameters are:
What current flows through the bulb in this case : A light bulb is rated at 60 W when connected to 120V. What current flows through the bulb in this case
Compare sizes of clearwell needed for achieving compliance : A small city is evaluating disinfection requirements for their drinking water plant. With an average flow of 5 MGD and a peak flow of 9 MGD, determine the controlling CT factor (virus or giardia) when the water temperature is 23 degrees C. Typical pH..
Estimate what is the motors power consumption : A certain electric motor draws a current of 10 A whenconnected to 120V. hat is the motor's power consumption
Determine the value of p for which motion occurs : Two 8-kg blocks A and B resting on shelves are connected by a rod of negligible mass. Knowing that the magnitude of a horizontal force P applied at C is slowly increased from zero
With what velocity will air exit under a small crack in the : Laboratory clean rooms are often kept at a slightly higher pressure than ambient pressure in order to flush out particulates and keep dust from getting in. If the pressure in such a room is equivalent to 1 mm water greater than the surrounding rooms
How far is the surface of the snow from the device : A sonic depth gauge is placed 5m above the ground. Anultrasound pulse sent downward reflects off snow depth depends onthe device using the correct air temperature is 0C. How far is the surface of the snow from the device
Design the rapid-mix system by providing water point : The town of Eau Gaullie has requested proposals for a new coagulation water treatment plant. The design flow for the plant is 0.1065 m 3 /s. The average annual water temperature is 19'C. The following design assumptions for a rapid-mix tank have been..
Determine the force it exerts on the path when it arrives : A 2-kg block slides on the smooth circular path (Quadrant One of full circle, block moving left to right). If it is released from rest when theta=0 degrees, determine the force it exerts on the path when it arrives at Point A (Located theta=30 degree..

Reviews

Write a Review

Civil Engineering Questions & Answers

  Estimate exponential rate of growth that would produce numb

World population reacted 4billion in 197 Use the doubling time approximation (3.5) to estimate the exponential rate of growth that would produce those numbers. Use the exponential growth equation (3.6) to find the growth rate

  Estimate its load carrying capacity assuming a safety factor

A 12 m-long and 800 mm-diameter drilled pier is constructed in a clayey soil with a1.5 m-diameter bell at the base. The top 7 m of the clay has an average Cu of 40 Kpa and the clay underneath has a Cu of 90 Kpa

  Determine relationship between discharge and parameters

The flow is fully developed and laminar. Make use of the Navier Stokes equation to determine the relationship between the discharge and the other parameters involved, for the case in which the change in pressure along the channel is zero.

  Determine the required mass of block a from rest

Determine the required mass of block A so that when it is released from rest it moves the 5-kg block B a distance of .75m up along the smooth inclined plane in t=2s. Neglect the mass of the pulleys and cords.

  Calculate the carbon content required at surface of steel

A 0.02wt% C steel is to be carburized at 1200°C in 4 hrs with a point 0.6mm beneath the surface reaching 0.45wt%C. calculate the carbon content required at the surface of the steel.

  How many tons of aggregate will be needed

The allowable stress in a steel shaft with an outside diameter of 1.5in and an inside diameter of 1.1in is 12,000psi. What hp can the shaft deliver at 1750rpm?

  Show by counter example that if f isnot onto then

Suppose that F1 ο G2 =F1ο G1 then F : S→ T, G1 : T → U, G2 :T →U,. Define a function F : R2 ? R2 by F(x, y) = (x +y, x - y). . Show that if F is onto, Suppose that G1ο F = G2 ο F.

  How will alum floc described in part d need to enter basin

A water treatment plant with a maximum daily flow of 4.4 m3/s is treating surface water with a minimum ambient temperature of -1°C (30°F). The water is coagulated with alum and the alum floc was measured to have a settling velocity of 1.6 m/h at 1..

  Determine what will the discharge be in each branch

A 48-in water main carries 79 cfs and branches into two pipes at point A. The branching pipes are 36 and 20 in. in diameter and 2800 and 5000 ft long, respectively. These pipes rejoin at point B and again form a single 48-in.

  Derive an equation for the undrained shear strength of clay

if a clay slope at a construction site fails derive an equation for the undrained shear strength of the clay given that the shear reistance along L of the slope can be given as: (SuH0)/ sin beta

  Determine the emissions of heat-trapping carbon dioxide

Emissions of heat-trapping carbon dioxide (CO2) reached an all-time high of 31.6 gigatons in 2011, a 3.2% increase over 2010. The International Energy Agency said this further reduces the chance that the world can avoid a dangerous rise

  What size of orifice is needed to produce a change in head

What size of orifice is needed to produce a change in head of 9m for a discharge of 2 m^3/s of water in a 1-m diameter pipe.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd