With what velocity will air exit under a small crack in the

Assignment Help Civil Engineering
Reference no: EM13562600

Laboratory clean rooms are often kept at a slightly higher pressure than ambient pressure in order to flush out particulates and keep dust from getting in. If the pressure in such a room is equivalent to 1 mm water greater than the surrounding rooms, with what velocity will air exit under a small crack in the door? Assume that viscous effects are negligible, i.e., that no energy is lost in the flow

Reference no: EM13562600

Questions Cloud

What current flows through the bulb in this case : A light bulb is rated at 60 W when connected to 120V. What current flows through the bulb in this case
Compare sizes of clearwell needed for achieving compliance : A small city is evaluating disinfection requirements for their drinking water plant. With an average flow of 5 MGD and a peak flow of 9 MGD, determine the controlling CT factor (virus or giardia) when the water temperature is 23 degrees C. Typical pH..
Estimate what is the motors power consumption : A certain electric motor draws a current of 10 A whenconnected to 120V. hat is the motor's power consumption
Determine the value of p for which motion occurs : Two 8-kg blocks A and B resting on shelves are connected by a rod of negligible mass. Knowing that the magnitude of a horizontal force P applied at C is slowly increased from zero
With what velocity will air exit under a small crack in the : Laboratory clean rooms are often kept at a slightly higher pressure than ambient pressure in order to flush out particulates and keep dust from getting in. If the pressure in such a room is equivalent to 1 mm water greater than the surrounding rooms
How far is the surface of the snow from the device : A sonic depth gauge is placed 5m above the ground. Anultrasound pulse sent downward reflects off snow depth depends onthe device using the correct air temperature is 0C. How far is the surface of the snow from the device
Design the rapid-mix system by providing water point : The town of Eau Gaullie has requested proposals for a new coagulation water treatment plant. The design flow for the plant is 0.1065 m 3 /s. The average annual water temperature is 19'C. The following design assumptions for a rapid-mix tank have been..
Determine the force it exerts on the path when it arrives : A 2-kg block slides on the smooth circular path (Quadrant One of full circle, block moving left to right). If it is released from rest when theta=0 degrees, determine the force it exerts on the path when it arrives at Point A (Located theta=30 degree..
Evaluate what is the final velocity of the probe : A 6090 kg space probe moving nose first toward Jupiter at 105m/s relative to the Sun fires its rocket engine, What is the final velocity of the probe

Reviews

Write a Review

Civil Engineering Questions & Answers

  You are planning a polaris observation at latitude 42 degree

You are planning a Polaris observation at latitude 42 degrees North when the star is at or near upper culmination. You want to know the error in azimuth that will result from a 1 min timing error. You know that the meridian angle, t, is exactly 0 deg..

  Find the moment equations and then the deflection

a simple beam with a pin support at A on the left side of my beam, and a roller connection 20 feet away on the far right side of the beam labeled C, with the midspan point (10 feet) labeled B.

  By what factor must the length of the current board be

A diving board of uniform cross-section is designed to deflect 6" under the weight of a 150 pound person standing on the end. With the recent trend towards obesity

  Calculate what is the bod5 of the river water

A BOD5 test sample of river water has the following test data. DO on day 0 = 7.9 mg/L. DO on day 5 = 2.3 mg/L. What is the BOD5 of the river water

  Determine what is the magnitude of the maximum stress

What is the magnitude of the maximum stress that exists at the tip of an internal crack having a radius of curvature of 5.5× 10-4 mm (2.165 ×10-5 in.) and a crack length of 3.5 ×10-2 mm (1.378 × 10-3in.)

  Determine what should be the diameter of each basin

A 4 mgd water treatment planet is being designed for an overflow rate of 0.5 gpm/ft^2. If two circular sedimentation basins will be used at al times, what should be the diameter of each basin

  Find the speed of the blocks after block

Block one has a mass of 1.5kg. Block two has a mass of 3.0kg. Treatthe pulleys as hoops. The radius of pulley one is 8.70m. The massof pulley one is 4.5kg.

  Difference between total and static pressure

The difference between the total and static pressure before a shock is 75 psi. What is the maximum static pressure that can exist at this point ahead of the shock? The gas is oxygen.

  1 discuss the different agencies institutes centers and

1 discuss the different agencies institutes centers and other national bodies that are involved in environmental work

  What do you think is the best ratio of b/y to use in your

A canal of rectangular cross-section and an n=0.030 is to be laid on a slope of 0.002 and is to carry a discharge of 30 m3/s. Calculate the cross-sectional area required for the channel to carry this flow based on the norma

  Determine the rate of ammonia nh4-n utilization and the

Determine the rate of ammonia (NH4-N) utilization and the biomass growth rate for the following conditions:

  Determine sequent depth and length of the hydraulic jump

A spillway carries a discharge of 22.5 m^3/s with the outlet velocity of 15 m/s at a depth of .2 m. Select an adequate USBR stilling basin and determine the sequent depth, the length of the hydraulic jump and the energy loss.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd