mechanical design and development, Mechanical Engineering

Assignment Help:

The major assignment for the unit is to design the final drive for the F-SAE race car. This is a group project to be completed with groups of up to 5 people. The design should be ready for manufacture by the end of the semester. The final drive that includes the final gear pair and differential housing, hubs and bearings, is intended to be the design for the next several years. The final gear pair must fit the existing output shaft of the engine, the differential must accommodate existing differential internals, the differential hubs must accommodate the existing tripod CV joint and the entire assembly must fit within the supplied envelop.
The assignment deliverables for the final drive assembly are as follows:
1. A complete set of design documents for the final drive assembly:
? A design report that details (30%):
? Market research
? Product design specification
? Concepts and evaluation
? Manufacturing details (including timeline)
? Cost estimates
? An analysis report that covers (30%):
? Load calculations
? Strength and stiffness calculations
? Finite Element Analysis of component(s)/assembly where applicable
? A complete set of manufacturing drawings (15%)
? SolidWorks 3D model of the final drive assembly (10%)
2. An informal 5-10 minute presentation of your group’s final drive assembly design to the class during the final lecture (5%).
The final 10% of the mark is based on report quality, such as grammar, referencing, presentation, etc. The written component of the design report should not exceed 20 pages, any content beyond 20 pages will not be considered in the mark. The analysis report should not exceed 20 pages, any content beyond 20 pages will not be considered in the mark.

Related Discussions:- mechanical design and development

Orthographic projections, Orthographic Projections: As you learned pre...

Orthographic Projections: As you learned previously about the theory of projection of points, planes and lines, the next significant is the projection of solids that have thre

Corrosion resistance of the austenitic stainless steels, The corrosion resi...

The corrosion resistance of the austenitic stainless steels (within the concentration and temperature conditions described above) relies on the formation and stability of a passive

Evaluate the crippling load, A cast iron hollow column, having 100mm extern...

A cast iron hollow column, having 100mm external diameter and 80mm internal diameter is used as a column of 2.4 m length. Using Rankine formula, calculate the crippling load, when

Kinetics of rigid bodies, Kinetics of Rigid Bodies: For the bodies und...

Kinetics of Rigid Bodies: For the bodies undergoing plane motion, a common scheme for solutions is to apply the equations of dynamic equilibrium as below. ∑ F x  = m a x

Illustrate all the laws of mechanics, (a) Illustrate all the laws of mechan...

(a) Illustrate all the laws of mechanics? (b) What ate the two limits of limitation on Newtonian mechanic?

Reciprocatin compressor - , Reciprocatin Compressor. It is taken in use to...

Reciprocatin Compressor. It is taken in use to compressor gases. ( kE 2  - kE 1) = 0, ( pE 2  - pE 1) = 0 q 1-2  - w 1-2 = ( h 2  - h 1 ) + 0 + 0 - q 1-2  - (- w

Beam and types of beam - support reaction, Beam: Sol.: A beam can be...

Beam: Sol.: A beam can be defined as a structural element which has one dimension (length) considerable larger As compared to the other two direction, which is breadth an

Relation between stress and strain, Relation between stress and strain: ...

Relation between stress and strain: The relation between stress and strain is generally shown by plotting a stress-strain (σ -e) diagram. Stress can be plotted on ordinate (ve

Working principle of carburettor , Working Principle of Carburettor : All ...

Working Principle of Carburettor : All carburettors work on one basic principle, the venturi. A venturi is a very simple device that changes air pressure by changing the velocity

What are the need of a surface condensing, (a) What are the need of a surfa...

(a) What are the need of a surface condensing ? Write disadvantages and advantages of Jet condenser and surface condenser. (b) A surface condenser is designed to handle 10000 Kg

Write Your Message!

Captcha
Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd