Thermal Systems Analysis and Design, Mechanical Engineering

Thermal Systems Analysis and Design, Mechanical Engineering

Assignment Help:

Create Visual Basic function ffactor(Re, rr) that calculates the Darcy-Weisbach friction factor in a pipe or duct, where Re is the Reynolds No. and rr is the relative roughness, using Churchill''s expression. Verify your results using the data given.
1. Liquid ammonia (? = 0.4 cSt, SG = 0.65) is delivered from a large pipe at 300 kPa to a 2 cm nozzle through 150 m of 4 cm horizontal commercial steel pipe, 3 elbows, and a globe valve. The nozzle is 20 m above the supply pipe. The valve is fully open.
a) Solve for the flow using an initial guess of 1 L/s.
b) Solve for the required pipe diameter and K for the globe valve for a flow of 4 L/s. The pipe is available in 2 cm diameter increments.
Put (a) and (b) on separate worksheets labeled 1a, 1b.

Related Discussions:- Thermal Systems Analysis and Design

Welding procedure and performance qualification, WELDING PROCEDURE AND PERF...

WELDING PROCEDURE AND PERFORMANCE QUALIFICATION A total quality assurance scheme, embracing all aspects of manufacture would have necessarily made all attempts to ensure

Handling tools and equipment for skid, Q. Handling tools and equipment for ...

Q. Handling tools and equipment for skid? Lifting or pulling and provisions for transportation of skid shall be in accordance with GS-904-0103, other relevant parts of contract

Design bulk materials storage, Q. Design Bulk Materials Storage? Consid...

Q. Design Bulk Materials Storage? Consideration shall be given to providing access to safety showers in areas of hazardous bulk material handling and storage. Where bulk handli

Check ferrite content of austenitic stainless steel weld, Q. Check ferrite ...

Q. Check ferrite content of austenitic stainless steel weld? Check the ferrite content of each austenitic stainless steel weld, including overlay welds, in the as-welded condit

Explain tee joints, Tee joints -The square tee joint requires a fillet weld...

Tee joints -The square tee joint requires a fillet weld that can be made on one or both sides. It can be used for light or fairly thick materials. For maximum strength, considerabl

Gas metal arc welding (gmaw), GAS METAL ARC WELDING (GMAW) GMAW is abbr...

GAS METAL ARC WELDING (GMAW) GMAW is abbreviation for Gas shielded Metal Arc Welding. Here fusion is achieved by an electric arc formed between work piece and process is called

Determine the buckling load, (a) Evaluate the buckling load of column with ...

(a) Evaluate the buckling load of column with one end fixed other free of 8m length by using Euler's formula. Given : I min = 1390m 4 E = 2 X 10 5 N/mm 2 (b) Derive a

Pulleys, what do you mean by law of belting and also explain the crowning o...

what do you mean by law of belting and also explain the crowning of pulleys ?

Introduction service and maintenance procedures , INTRODUCTIO : In Motorc...

INTRODUCTIO : In Motorcycle Servicing, we studied about servicing of a motorcycle. Here, you will study about the detailed procedures for motorcycle service and maintenance. The s

Reaction forces, If the allowable shear stress for each of the 10-mm-diamet...

If the allowable shear stress for each of the 10-mm-diameter steel pins at A, B, and C is tallow = 90 MPa, and the allowable normal stress for the 13-mm-diameter rod is sallow = 15

Write Your Message!

Name

Email id

Message

Verfication Code

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd