MATLAB, Electrical Engineering

Assignment Help:

Flicker noise: I’d like to plot the graph of the flicker noise found in the data sheet for the amplifier (will be provided later) and also generate the equation for that graph showing the coefficient for each term . Beside, please note that graph is in log scale.
Secondly, I’ll send you the code for the TRANSFER FUCTION I already did in Matlab and I want you to use the equation to FIND the INTEGRATION of the two equations ( flicker noise x Transfer function) and plot the graph for the multiplications of the two equations. Or you can write another code (if that’s easier for you) for the transfer function of the bandpass filter with the following specifications :
Unnormalized Chebyshev-I analogue filter:
Selectivity: Bandpass
Implementation: Analogue
Order: 4th-order

pass band frequency 1 =300Hz
pass band frequency 2 =3000Hz
stop band frequency 1 =100Hz
stop band frequency 2 =9000Hz
apass=-1dB
astop=-22dB

Last part, I’d like you to implement the transfer function into real components (resistors and capacitors) using Psipice and build up Bandpass filter Sallen Key 4th order circuit, then make sure that both graph and central frequency are the same for the two cases ( transfer function Matlab and the Psipace version).
Important points to take into consideration:
- The code must be fully commented with explanation of every function and line of the code as much as possible. So it’s easy to follow and readable
- The frequency to work with is 4500Hz and Bandwidth 100Hz


Related Discussions:- MATLAB

Stator current control methods - motor control , Stator  Current Control ...

Stator  Current Control Methods The torque  and speed  of an induction motor  can be  controlled  by the  stator  current  the motor  behaviour  is different from that with VS

Semiconductor equations, Semiconductor Equations  The semiconductor e...

Semiconductor Equations  The semiconductor equations that are relating these variables are shown below: Carrier density: n = n i exp (E FN - E i / KT)        (1)

Utilization of electrical energy, Ask question #Discuss the role of load fa...

Ask question #Discuss the role of load factor on the cost of electrical energy 100 words accepted#

Illustrate how to replace the ht fuse, Illustrate how to replace the HT Fus...

Illustrate how to replace the HT Fuse on a 6-pole and 4-pole structure? Ans: a) Open switch on 6-pole or 4-pole. b) Connect the discharge rod between earth and conduc

Find the small-signal equivalent circuit parameters, Given that a BJT has β...

Given that a BJT has β = 60, an operating point defined by I CQ = 2.5 mA, and an Early voltage V A = 50 V. Find the small-signal equivalent circuit parameters g m , r o , and rπ.

Dc motors, costruction and working of dc motor

costruction and working of dc motor

Power diode - power semiconductor devices , Power Diode A power diode i...

Power Diode A power diode is a two terminal, anode a and cathode K and  two layer P  and  N  junction devices. A PN  junction normally  formed  by allowing  diffusion and epita

Bode plot phase ad gain margin, Using Bode plot calculate (a) Phase margin ...

Using Bode plot calculate (a) Phase margin (b) Gain margin (c) Stability of closed loop system. The open transfer function of the system is t=30/(s+2)/(s+3)Using Bode plot calcula

Determine lower and upper cut-off frequency, Q. In an amplifier, the maximu...

Q. In an amplifier, the maximum voltage gain is 1500 and occurs at 1kHz. It falls to 1060.5 at 20kHz and at 20Hz. Determine (i) lower cut-off frequency (ii) upper cut-o

Write Your Message!

Captcha
Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd