Hardness testing, Mechanical Engineering

Assignment Help:

After final PWHT, the hardness of the deposited weld metal and heat affected zone (HAZ) shall be examined. Hardness values shall not exceed 200 BHN. Heat treatment shall be performed, if required to reduce hardness to the specified level, subject to review and approval by WorleyParsons Canada.

On drums, hardness shall be measured one on each of the following welded areas:

a. Circumferential

b. Longitudinal

c. Nozzle

d. Stub

e. Attachment

Hardness test shall be made with a Brinell Testing machine or a portable hardness tester such as a Telebrineller using a 10 mm (3/8") ball.

Submerged arc weld, SAW shall be tested for hardness on the weld and on the HAZ. The values shall not exceed 200 BHN.

Where required value of BHN is not achieved, the fabricator shall perform a retest without any heat treatment whatsoever. If this second test fails to meet the BHN requirement, heat treatment shall be repeated. Methods and procedures for anticipated second heat treatment shall be pre-approved by WorleyParsons Canada.


Related Discussions:- Hardness testing

What do you mean by thermil-welding, What do you mean by Thermil-welding ? ...

What do you mean by Thermil-welding ? Describe the process with neat sketch.

Assignment, A cantilever beam is loaded with a concentrated. Force of 5kN a...

A cantilever beam is loaded with a concentrated. Force of 5kN at the free end. The length of the cantilever beam is 1m having cross section of 50×50mm. determine the equation for b

Find velocity and acceleration of the slider , Question: The disk 3 sho...

Question: The disk 3 shown in the figure rotates at a constant angular velocity w 3 = 2.0 rad/s. A slider in a slot in the disk causes rod 2 to rotate.  When the slider

Electrode wire for co2 welding, ELECTRODE WIRE FOR CO2 WELDING CO 2 we...

ELECTRODE WIRE FOR CO2 WELDING CO 2 welding wire must have a special composition to withstand the oxidising nature of the CO 2 arc atmosphere. Though, CO 2 is not reactive a

Working of engine lubrication system , Working of Engine Lubrication System...

Working of Engine Lubrication System: The oil flows from oil pump into the distribution chamber, where it is divided into two parts. One part enters into the right crankcase cove

Thermodynamics, You wish to boil 1.2 kg of water, which has a specific heat...

You wish to boil 1.2 kg of water, which has a specific heat capacity of 4186 J/kg-K. The water is initially at room temperature (293 K). Water boils at 373 K. How much energy must

Illustrate theories in planning a machining sequence, Illustrate theories i...

Illustrate theories in planning a machining sequence A component requires several machining operations to bring it to a final shape. The sequence of these operations are arran

Ratio of applied stress, Ratio of applied stress: What should be the r...

Ratio of applied stress: What should be the ratio of applied stress, s, to yield stress s Y in a large thin plate so that plastic spread along lint of crack is equal to  1 /1

Important section of fly-overs and underpasses, Important section of fly-ov...

Important section of fly-overs and underpasses: Culverts : A structure having a waterway upto 5 m. Minor Bridge : A structure having a waterway of 6-30 m. Medium Si

Mass and heat transfer, a hot brass plate is having its upper surface coole...

a hot brass plate is having its upper surface cooled by impinging jet of air at temperature of 15 degree celcius

Write Your Message!

Captcha
Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd