Explain working of ammeter, Electrical Engineering

Assignment Help:

Q. Explain working of Ammeter?

In order to measure the current through a wire or line of a circuit, an ammeter is connected in series with the line. A practical ammeter can usually be modeled as a series combination of an ideal ammeter and an internal resistance RI. The potential difference between the two terminals of an ideal ammeter is zero, which corresponds to zero internal resistance. There are what are known as dc ammeters and ac ammeters. An ac ammeter usually measures the rms value of the time-varying current. Note that for the ammeter to be inserted for measuring current, the circuit has to be broken, whereas for the voltmeter to be connected for measuring voltage, the circuit need not be disassembled.

Multimeters that measure multiple ranges of voltage and current are available in practice. Ohmmeters measure the dc resistance by the use of Ohm's law. A multimeter with scales for volts, ohms, and milliamperes is known as VOM. An ohmmeter should not be used to measure the resistance of an electronic component that might be damaged by the sensing current.


Related Discussions:- Explain working of ammeter

Define power-supply rejection ratio, Q. Define Power-Supply Rejection Ratio...

Q. Define Power-Supply Rejection Ratio? An op amp's ability to disregard changes in power-supply voltage is measured by the power- supply rejection ratio (PSRR), which is speci

Details of a distribution transformer, Electrical network details: 1  ...

Electrical network details: 1          single line diagrams with conductor sizes, transformer locations, consumer location, lengths, capacitors, and load, etc., 2

Energy stored in the capacitor when it is fully charged, An 12µF capacitor ...

An 12µF capacitor is connected in series to a 0.5M? resistor across the dc voltage supply of 240V. verify: (a)  Time constant (b)  Initial charging current (c)  Time fo

Three phase ac circuit, Three Phase AC Circuit: Alternating circuits t...

Three Phase AC Circuit: Alternating circuits thus far discussed have single phase supply system and it's satisfactory for domestic application as light, fan and heating, etc.

Commercial fm radio broadcasting, Q. Commercial FM radio broadcasting? ...

Q. Commercial FM radio broadcasting? Commercial FM radio broadcasting utilizes the frequency band of 88 to 108 MHz for the transmission ofmusic and voice signals. The carrier

Determine l and c of the band pass filter circuit, Q. Determine L and C of ...

Q. Determine L and C of the band pass filter circuit of Figure to have a center frequency of 1 MHz and a bandwidth of 10 kHz. Also find the Q of the filter.

How address and data lines are demultiplexed in 8085, How address and data ...

How address and data lines are demultiplexed in 8085? AD0-AD7 lines are multiplexed and the lower half of address A0-A7 is available only during T1  of the machine cycle. This

How to calculate back pitch, Q.   A 6 - pole, DC armature with 36 slots and...

Q.   A 6 - pole, DC armature with 36 slots and 2 coil - slides/slot is to be wave wound (double layer). Calculate the back pitch, front - pitch and commentator pitch. How many dumm

Find the forced component of the current, Q. Consider an RC parallel circui...

Q. Consider an RC parallel circuit excited by (a) i(t) = 20e -2t A, and (b) i(t) = 20 A. Find the forced component of the current through the capacitor for R = 2  and C = 2F.

Sketch the phasor diagram, Consider an RLC series circuit excited by v (t) ...

Consider an RLC series circuit excited by v (t) = 100√2 cos 10t V, with R = 20 , L = 1 H, and C = 0.1 F. Use the phasor method to find the steady-state response current in the cir

Write Your Message!

Captcha
Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd