Explain priority interrupts of 8085, Electrical Engineering

Assignment Help:

Explain priority interrupts of 8085.

The 8085 microprocessor has five interrupt inputs. They are TRAP, RST

.5, RST 6.5, RST 5.5, and INTR. These interrupts have a fixed priority of interrupt service.

If two or more interrupts go high at the similar time, the 8085 will service them on priority basis. The TRAP has the highest priority followed by RST 7.5,

RST 6.5, RST 5.5. The priority of interrupts in 8085 is shown in the table.

Interrupts Priority

TRAP

RST 7.5

RST 6.5

RST 5.5

INTR

 


Related Discussions:- Explain priority interrupts of 8085

Design of matching networks for amplifiers, Design a low noise amplifier us...

Design a low noise amplifier using an Infineon RF transistor BFP640. The amplifier is to be used to amplify the L2 GPS signal and so the centre frequency is 1227MHz and bandwidth 4

Explain the working of elecro static precipitator, With the help of neat an...

With the help of neat and clean diagram illustrate the working of Elecro Static Precipitator (ESP). Describe the following: (a) Coal Handling Systems (b) Coal Storage

What do you mean by direct coupling, Q What do you mean by Direct coupling?...

Q What do you mean by Direct coupling? In this method the a.c. output signal is fed directly to the next stage. No reactance is included in this coupling network. Special d.c.

Configured the dual processor architecture, Configured dual processor archi...

Configured dual processor architecture  In centralized SPC, dual processor architecture can be configured to operate in following one of three modes: 1.  Standby mode: In

Compute the source current, Q. A 230-V, single-phase, 60-Hz source supplies...

Q. A 230-V, single-phase, 60-Hz source supplies two loads in parallel. One draws 10 kVA at a lagging power factor of 0.80 and the other draws 6 kWat a lagging power factor of 0.90.

Pneumatic circuit diagram, FIGURE shows a pneumatic circuit diagram used fo...

FIGURE shows a pneumatic circuit diagram used for air supply and exhaust in an automatic control system.  (a) Name all symbols (including pipelines) used in the system. (b) N

Find a minimum two level, Find a minimum two level, multiple-output AND-OR ...

Find a minimum two level, multiple-output AND-OR gate circuit to realize these functions (eight gates minimum). F 1 (a,b,c,d) =Σm(10,11,12,15) +D (4,8,14) F 2 (a,b,c,d) =Σm(4

Indicate the condition of the overflow and carry bits, Q. Do the following ...

Q. Do the following operations with 8 bit bytes, and indicate the condition of the overflow and carry bits. a) 10111011 + 00000011 b) 11101101 + 11111001 c) 11011011 + 110

Engineer, Transmission Through a LiNb0 3 Plate Examine the transmission of...

Transmission Through a LiNb0 3 Plate Examine the transmission of an unpolarized He-Ne laser beam (?o= 633 nm) normally incident on a LiNb0 3 plate (ne = 2.29, no = 2.20) of thickn

Common-base configuration, Common-base configuration:  The common-bas...

Common-base configuration:  The common-base that is abbreviated as CB transistor configuration, which is as well termed as the 'grounded base' configuration, is displayed in

Write Your Message!

Captcha
Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd