Electricity and gas hazards, Electrical Engineering

Assignment Help:

Electricity beyond doubt is very useful and essential for us; but if dealt with carelessly, it can prove to be very fatal. It is compulsory for a laboratory assistant to be sure of the colour code of electric wires. The person should be able to calculate the current for different electrical appliances. To prevent any hazard from electricity, one should follow a safe conduct i.e., proper use of adaptors, plugs and also the cable and flex routing. One should keep checking every plug, socket and lead in the laboratory from wire to wire. Earthing is also very important while dealing with electricity. It is essential to learn how a piece of equipment can be earthed and also to test the connections. ELCBs are in large use for this purpose. The lab assistant should be aware of other types of dangers occurring because of electricity.

We learnt how LPG can be used safely. Pressurised gas cylinders are widely used in all labs and many cylinders contain toxic or flammable gases. Proper precautions should be followed while handling and using these cylinders. The laboratory personnel should be aware of the colour code of the cylinders used which is specific for a particular gas. Knowledge of gas leak detection and handling and the emergency treatment in the event of an exposure is essential for every laboratory staff. Some simple procedures are made use of to detect the gas leakage like, use of ammonia for chlorine, lead acetate for hydrogen sulphide etc. The possible health hazards of different gases and the emergency treatment in case of an eventuality have been given in a tabular form. The use of goggles should be made as a precautionary measure in case of a possible implosion in evacuated glass apparatus.

 


Related Discussions:- Electricity and gas hazards

Show applications for synchronous motors, Q. Show Applications for Synchron...

Q. Show Applications for Synchronous Motors? With constant-speed operation, power factor control, and high operating efficiency, three-phase synchronous motors are employed in

Fault analysis, The one line diagram of a simple three phase power system i...

The one line diagram of a simple three phase power system is shown in figure below. Each generator is represented by an emf behind the transient reactance. All impedances are expre

Illustrate how to replace the ht fuse, Illustrate how to replace the HT Fus...

Illustrate how to replace the HT Fuse on a 6-pole and 4-pole structure? Ans: a) Open switch on 6-pole or 4-pole. b) Connect the discharge rod between earth and conduc

Explain open loop control systems, Explain Open Loop Control Systems In...

Explain Open Loop Control Systems In an open-loop control system, the controller independently computes exact voltage or current required by the actuator to do the job and send

How monitoring and control has be done, How control and monitoring has be d...

How control and monitoring has be done - Sensors gather information from application being monitored or controlled. - The data being gathered is frequently analogue in natur

Find the decibels of improvement in signal-to-noise ratio, If a compressor ...

If a compressor in a system can change a message crest factor from 3.2 to 2, while maintaining its peak amplitude constant, find the decibels of improvement in signal-to-noise rati

Registers - introduction to microprocessors , Registers A resister is ...

Registers A resister is  a group  of flip  flops  or binary  cells which holds  the binary information. Since  a binary cell  stores  one  bit of  information  an n bit  regis

Testing stationarity, 1)  Use plot of the stock return and consider the Aut...

1)  Use plot of the stock return and consider the Autocorrelation Function to determine the auto-regressive structure of the data and explain why you think the return is stationary

MATLAB, Flicker noise: I’d like to plot the graph of the flicker noise foun...

Flicker noise: I’d like to plot the graph of the flicker noise found in the data sheet for the amplifier (will be provided later) and also generate the equation for that graph sho

Is the quantizer midriser or midtread, Q. The quantum levels of a quantizer...

Q. The quantum levels of a quantizer are separated by the step size δv = 0.2 V, with the lowest and highest levels of-3.3 V and +3.3 V, respectively. A sequence ofmessage sample

Write Your Message!

Captcha
Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd