Drive chain cleaning and adjustment , Mechanical Engineering

Assignment Help:

Drive Chain Cleaning and Adjustment : The service life of the drive chain depends on proper lubrication and adjustment. Poor maintenance can cause premature wear or damage to drive chain and sprockets. Under severe riding and use in the dusty areas frequent maintenance would be necessary.

STEPS

  • Remove the lower chain cover of the drive chain.
  • Keep a tray below the drive chain.
  • Clean the drive chain using kerosene with the help of a brush and air dry.
  • After drying, lubricate the drive chain with SAE 90 lubricant.
  • Check the slackness of drive chain. It should be between 20-30 mm.
  • If required adjust the drive chain. To adjust loosen the axle nut and sleeve nut.
  • Adjust the chain slackness by adjusting the chain adjuster nut.
  • Drive chain is adjusted equally on both the sides by ensuring the scale graduations on both the sides of the swing arm are coinciding with the notch on the adjusting plate
  • Clean the chain cover. Install the chain cover securely.

Important points to remember:

  • Chain slackness must be between 20-30 mm.
  • Open end drive chain lock plate should be fitted in the opposite direction of the chain rotation.

 


Related Discussions:- Drive chain cleaning and adjustment

How will you measure the engine oil level?, (a) Why do we change the engine...

(a) Why do we change the engine oil at periodic intervals? (b) What are the recommended instructions to change engine oil? (c) How will you measure the engine oil level?

Find out load carried and compressive stress - steel bar, Find out load car...

Find out load carried and compressive stress: The concrete column 300mm x 300mm in section can be reinforced by 10 longitudinal 20mm diameter round steel bars. The column car

Concept and application of limiting friction, Concept and application of li...

Concept and application of limiting friction: Sol.: The maximum value of frictional force that comes into play, when the body just begins to slide over the surface of the ot

Explain clamping devices, Explain Clamping Devices A clamp is a d...

Explain Clamping Devices A clamp is a device that holds the work piece firmly against the locators provided and also resists all forces generated by the cutting action of

#title.scale, actual division 2km is shown as 1 cm in a map.construct a cle...

actual division 2km is shown as 1 cm in a map.construct a clean scale to measure km which can travel a distance upto 30 km.Show measurement of 18 km in the scale

determine the mass of air, An amount of air contained in a rigid container...

An amount of air contained in a rigid container is at  T1 = 300 K.  After adding 450 kJ of heat, the air temperature increases to  T2 = 430 K.  Determine the mass of air,  m [kg],

RC circuit, #question.I am doing a ,ini project on Hovercrafts .As i am fro...

#question.I am doing a ,ini project on Hovercrafts .As i am from mechanical i need assistance regarding control over brushless motors.

Fuels and lubrication technology, minimum mass of air required for complete...

minimum mass of air required for complete combustion of the HFO

Seasonal-component analysis, Seasonal-Component Analysis: A food proce...

Seasonal-Component Analysis: A food processor uses a moving average to forecast next month's demand. Actual demand data for the past few months is available as depicted in the

Terminal nut-terminologies of spark plug , Terminal Nut: This is a detach...

Terminal Nut: This is a detachable type of terminal nut. The high tension (HT) cord is connected here. This is also available in non-detachable type. Figure: Spark Plug

Write Your Message!

Captcha
Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd