Distributed Control Sytems, Electrical Engineering

Assignment Help:
1. Produce a fully-labelled sketch to show the components of a Direct
Digital Control system.

2. State the minimum number of printed-circuit cards required to construct a
basic controller, naming each of the cards.

3. Produce a sketch to show the construction of the data words on the data
highway.

4. Explain the use of the different MODES of control available in a
controller of a Distributed Control System.

5. The Instrument Engineer, designing a Distributed Control System, has
available to him Basic Controllers and Advanced Controllers. List all
the reasons why an Advanced Controller might be used in preference to a
Basic Controller, making reference to the full processing capabilities of
the advanced controller.

6. Describe the difference between notified status and change detect points
and list the types of cards to which this applies.

7. Describe the main purpose of sequence programmes and state what would
require to be done in the writing of a programme which was too long to fit
in one sequence slot, making reference to the problem which this could
cause.
8. Describe the data presented to the operator on the Detail page display of
the operator station. List six different items of data which would be
presented for a control loop data point, and state whether the operator
would be able to change the values pertaining to these items.

9. State the limitations of the data highway system and what attributes of the
advanced distributed control system help to overcome these.

10. Explain the token passing technique used for advanced distributed control
system communications on the LAN, describing the procedure for a
newly powered up module to join the system.

11. Describe in detail the different types of alarm generated on the advanced
distributed control system.

12. Using the information below, produce a set of calibration figures for the
control loop TICA1495.
TI1495 range = 100 to 420°C
TICA1495 SP = PV = 300°C
TCV1495 = 30%.

13. An operator, using the operator interface, will have the operator station in
operator personality. Describe the requirement for ''personalities'' within
the DCS, making reference to other personalities available, and explain
how different functions are denied to unauthorised persons within the
operator personality.

14. Describe a procedure for adding a new data point to the distributed
control system data base and making this new point available to the
operator.




15. Provide a list of the five major factors to be taken into account when
considering the choice of a distributed control system for any given
installation, stating the benefits to be gained from the use of DCS for an
offshore oil and gas processing plant.

16. Describe the differences in communication protocol between the
Honeywell TDC2000 and Honeywell TDC3000 distributed control
systems. State the name of the device used to enable these two systems to
talk to each other.

17. All of the distributed control systems have the ability to use a data
historian module. List the main tasks of a data historian attached to a
DCS.

18. Describe the use of Group Points, stating which of the manufacturer''s
systems these apply to.

19. Describe the functions of a Highway Traffic Director, and state which of
the manufacturer''s systems does not require the use of this device.

20. Where would an HIA be installed and what are its functions?

21. Explain the reasons behind the installation of distributed control systems
in refineries for the control of natural gas liquids fractionation plant.

Related Discussions:- Distributed Control Sytems

Digital Signal Processing, 1. Write a MATLAB program to generate and plot t...

1. Write a MATLAB program to generate and plot the signal x1(n) = [3 2 -2 0 7], n = 0,1,2,3,4.

What is a microcomputer, What is a microcomputer? A computer that is de...

What is a microcomputer? A computer that is designed using a microprocessor as its CPU is known as microcomputer

Digital transmission on fading multipath channels, Digital Transmission on ...

Digital Transmission on Fading Multipath Channels We have discussed thus far digital modulation and demodulation methods for the transmission of information over two types of c

Equivalent circuit of a polyphase induction machine, Equivalent Circuit of ...

Equivalent Circuit of a Polyphase Induction Machine The inductionmachinemay be regarded as a generalized transformer inwhich energy is converted and electric power is transferr

Nop no operation instruction , NOP No Operation Instruction No operati...

NOP No Operation Instruction No operation  is performed  when this  instruction is executed. The instruction format is             NOP All  registers and flags  re

Illustrate gray code, (a) In the so-called folded binary code of 4 bits, th...

(a) In the so-called folded binary code of 4 bits, the left most digit represents the sign of an analog signal's quantized samples (with 0 for negative and 1 for positive), and the

What is meant by a bus, A bus is a collection of conducting lines that carr...

A bus is a collection of conducting lines that carrier's data, address, & control signals. A bus is two or many wire communication technique. A bus which communicate among two

Explain stages of attending to rail fracture, Q. Explain stages of attendin...

Q. Explain stages of attending to Rail fracture? Various stages of attending to Rail fracture / weld failure in a L.W.R. track in field - Equipment required - i) Special

Primacy of mosfet, Primacy of MOSFET In the year 1959, Dawon Kahng an...

Primacy of MOSFET In the year 1959, Dawon Kahng and Martin M. (John) Atalla at Bell laboratory invented the MOSFET. Operationally and structurally diverse from the bipolar ju

Write Your Message!

Captcha
Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd