Design the nozzle connections, Mechanical Engineering

Assignment Help:

Q. Design the Nozzle Connections ?

Nozzle design shall be such that if the actual combined thickness of the shell or head and reinforcing pad exceeds 50 mm, either integrally reinforced nozzles or standard nozzles with the nozzle neck thickness equal to the shell or head thickness, as applicable, shall be used.

Nozzles, handholes and manway connections shall have a minimum wall thickness equivalent to extra heavy pipe.

‘Set-On' nozzle connections require prior approval.

Nozzle inside corners shall be radiused.

Nozzles NPS 2 and larger shall be seamless long welding neck flanges, or seamless pipe with welding neck flanges. Slip-on or lap joint flanges are not acceptable.

All nozzle connections shall be flanged. Threaded connections require written approval. Where threaded connections are permitted, the minimum size shall be ¾ in., 6000# rating.

Flange ratings for nozzles less than NPS 3 shall be 300# RF minimum.

The minimum inside diameter of manways shall be 508 mm unless specified otherwise on the Vessel Data Sheet. Manways shall be complete with davits for handling the manway covers, unless specified otherwise on the Vessel Data Sheet.
Nozzle or repad welds and attachments shall not overlap main seam welds or interfere with the welds of other attachments.

Vessel drains shall be flush with the inside shell or head surface and shall be located to ensure complete draining of the vessel.

Other nozzle connections may utilize an inside projection, subject to prior approval.

All manways and hand holes shall be provided with blinds, studs, nuts and an extra set of gaskets. Spares, drains, vents or other connections requiring blinds, shall be as specified on the Vessel Data Sheet.


Related Discussions:- Design the nozzle connections

Organization structure and design, Describe, using examples, what is meant ...

Describe, using examples, what is meant by job specialization, identifying it advantages and disadvantages.

Stresses., temparature stresses in composite bars

temparature stresses in composite bars

Find span of the beam, A beam is simply supported and carries a uniformly d...

A beam is simply supported and carries a uniformly distributed load of 40kn/m run over whole length or span. The section of the beam is rectangular having depth as 500mm. If the s

Angle of friction, Angle of friction:   It can be defined as t...

Angle of friction:   It can be defined as the angle made by resultant of normal reaction ( R ) and limiting force of friction ( F ) with normal reaction ( R ). Let,

Plate clutch for warpage-clutch jerking, Plate clutch for warpage : Place ...

Plate clutch for warpage : Place plate clutch on surface plate and check for warpage. Ensure that 0.20 mm feeler gauge does not slide freely.

Efficiency test on sand blasting, Efficiency Test on Sand Blasting:   ...

Efficiency Test on Sand Blasting:             After the study on sand blasting, the result was acceptable and the next step is planning to make order for new machine and searc

Nominal stress and true stress, Nominal Stress and True Stress: Nomina...

Nominal Stress and True Stress: Nominal stress is the ratio of force per initial cross sectional area (original area of cross section). Nominal stress = Force / initial ar

Illustrate about the strap footing, Illustrate about the strap footing? ...

Illustrate about the strap footing? In given demonstrates figure the exterior footing placed eccentrically under the exterior column so that property line limitations are not v

Steps of servicing- important points to remember, The water jet should not ...

The water jet should not directly fall on speedometer, spark plug, steering cone race and electrical connections. During washing there is a possibility of water entry below the sea

Burner management - discrete controls for steam generators, Q. Burner Manag...

Q. Burner Management - Discrete Controls for steam generators? The burner management system shall control the generator operation during pre-purge, light off, normal operation,

Write Your Message!

Captcha
Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd