Bidirectional shift register, Electrical Engineering

Assignment Help:

Design 2-bit bidirectional shift register?

## A list of ten 8-bit numbers is located at address $5000. Write a 68000

Assembly program (flowchart and code) to sort those numbers in an

Ascending manner,?

##Minimize the logic equation and realize the circuit afterwards?

                        _    _____

Y= (A+BC).(B+C).(A.B.C+B)                

##Design a 2-bit synchronous binary counter with hold control input ?

##Given the partial program:

                         MOVE #3, D0

                         EOR    D0, D0

                         AND     D0, D0

Is there any error in the program?

If not, how would D0 change?

 ## Write a 68000 assembly program to realize the C++ DO-While loop.?

 ## A list of ten 8-bit number is located at address $3000 .Write a 68000 program (flowchart and code ) to copy the number that are located at the odd addresses into a new list at address $7000?.

##. Using state assignment method, design a 3-bit binary counter with an

UP/Down count control input.?

###Convert the unsigned number> (11101101)2 to its decimal, octal, and hexadecimal equivalents?.

## the following operations:

(3411)8 -(267)8 and (ABCD)16 +(1234)16

##Write a 68000 assembly program to clear the contents of memory locations in the range $5000 to $6000?

##Draw the truth table of the Boolean equation given below. Minimize the circuit using any minimization techniques.

_______

(A+BC)   + (D+AB)


Related Discussions:- Bidirectional shift register

Operation performed by instruction out 47 h, Q. Illustrate the operation p...

Q. Illustrate the operation performed by instruction OUT 47 h, AL. Ans:  It transfers contents of AL to I/O port 47h. Notice that I/O port number appears as 0047h on the 16 b

Dc machines, explain dynamically induced emf and derive expression for it

explain dynamically induced emf and derive expression for it

Conveyor, The FESTO conveyer consists of 600mm belt driven by a 24V d.c. mo...

The FESTO conveyer consists of 600mm belt driven by a 24V d.c. motor at a rate of 13 seconds per metre. A relay on the FESTO panel controls the motor operation and is wired for sou

Find the modulated signal in each case, Let the message signal m(t) = α cos...

Let the message signal m(t) = α cos (2πf m t) be used to either frequency-modulate or phase- modulate the carrier Ac cos(2πf c t). Find the modulated signal in each case.

Coupling, different coupling methods

different coupling methods

Add register and carry with accumulator, Add Register and Carry with Accumu...

Add Register and Carry with Accumulator The contents  of register R and the  carry flag are added to the  contents of the  accumulator  and result of  addition  is also  sto

Electric roadway system specification, The electric roadway system shall ut...

The electric roadway system shall utilize solar energy as the main power source. The electric roadway system shall negotiate with the power utility on backup power supply.

Determine the resultant mmf, Q. The N-coil windings of a three-phase, two-p...

Q. The N-coil windings of a three-phase, two-pole machine are supplied with currents ia,ib, and ic, which producemmfs given by F a = Ni a cos θm; F b = Ni b cos(θm - 120°); and

Student, Can I get some ideas for power system stability simulation using M...

Can I get some ideas for power system stability simulation using Matlab?

Sid input - serial input output ports , SID  Input Serial input data  ...

SID  Input Serial input data  single  bit can be  accepted through this  pin using RIM  command  discussed in details in chapter8.

Write Your Message!

Captcha
Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd