User Account

All Pages

Balsa wood truss car design, Mechanical Engineering

Assignment Help:
design a car to be build by balsa wood trusses, the car has to be with in a specific dimension, calculations of forces on members and nodes using method of joints need to be done and failure analysis. A scale balsa wood model will be built and tested in order to compare with the predicted load capacity of the chassis.
Limited material quantities will be issued. Design a truss framework having maximum load capacity/minimum weight (see 2.12) with the loads at the
positions shown in Figure 1. The two truss sides are joined by cross-members that must be perpendicular to
the truss and whose mass is to be accounted for. There must be sufficient cross-members to prevent twisting
of the structure. Use truss analysis to predict the load at which the truss will fail under the testing procedure. Buckling of the framework struts is the most likely failure mode and in order to manage this, you may need
to increase the stiffness of the framework members under compression or reduce their length.
The buckling loads for members under compression may be calculated using the Euler strut buckling formula. I have the balsa wood characteristics and quantites

Related Discussions:- Balsa wood truss car design

Find the weight percent of austenite present in the steel, Find the weight ...

Find the weight percent of austenite present in the steel: A 0.4% C hypoeutectoid plain carbon steel is slowly cooled from 1540 o C to (i) slightly above 723 o C and (ii) s

Determine the chemical formulate for refrigerant, (a) Draw P-H and T-S diag...

(a) Draw P-H and T-S diagrams for following cases : (3) (i) Cycle with superheated vapour before compression. (ii) Cycle with sub-cooling or under-cooling of refrigerant.

What are the principles of location of drilling jig, a) Define the degree o...

a) Define the degree of freedom of a work piece in space. What are the basic principles of location of drilling jig.

Describe electron beam welding, Discuss any three of the following:- (i)...

Discuss any three of the following:- (i) Electron Beam Welding (ii) Friction Welding (iii) Thermit Welding (iv) Gas Welding Give their advantages, Limitations, and a

Tool signature , what is tool signature?

what is tool signature?

Necessity of cooling system , Necessity of Cooling System To preve...

Necessity of Cooling System To prevent the engine from excessive heating. To avoid the piston seizure due to thermal expansion. To prevent burning of lubricant a

Control system, hi i have an assignment in control system can u do it ?

hi i have an assignment in control system can u do it ?

Calculate the amount sand-aggregate, Calculate the amount of cement, sand,...

Calculate the amount of cement, sand, aggregate, and water needed to create a concrete mix with a 28-day compressive strength of 34 MPa for a 10 m x 10 m x 0.25 m structure given t

Gears, Gears : A gear is a disc with teeth on its boundary. If these teeth...

Gears : A gear is a disc with teeth on its boundary. If these teeth are formed at its inner boundary then this gear is known as an internal gear (annulus). These types of gears ar

Rankine cycle - thermodynamics, Rankine cycle - Thermodynamics: The ma...

Rankine cycle - Thermodynamics: The major problems of Carnot cycle is compressing very wet steam mixture from the condenser pressure up to boiler pressure. The trouble can be

Write Your Message!

Captcha
Order Assignment

Featured Services

Order Now

Popular Subjects

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +91-977-207-8620

Phone: +91-977-207-8620

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd