Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
The outline of the part in previous Problem 6.7 is to be profile milled using a 3D-nun diameter end mill with four teeth. The part is 15 mm thick. Cutting speed = 150 m/min and faced e 0.085 mm/tooth Us the lower left comer of the part as the origin in the .r- y axis Sybron. Two of the holes in the part have already been drilled and will be used for damping the part during profile milling. Write the part program in the word address corner with TAB parathion and variable word order. Use absolute positioning. The program style should be sun?
The pall Figure P6.7 is to be drilled on" tune-type drill press the part is 15.0mm thick there are three drill sizes to be used: 8 mm, 10mrn. And 12 mm. These drills are 10be specified in the part program by tool turret positions T01, T02, and T03. All tooling is high speed steel. Cutting speed = 75 nun/min and feed = 0.08 rum/rev. Use the lower left corner of ne part as the origin in the x-y axis system. Write the part program in the word address format with TAB separation and variable word order. ?
b) Draw the LFSR circuit to generate the CRC. Generate the CRC by applying the data pattern to the LFSR and verify the answer in part a. c) An error vector is given by X7+ X6+ X4+ X3+1. What is the received bit pattern corresponding to part a
Calculate capacitor size, An electrical supply company charges its consumers a penalty if their reactive energy consumption (Kvar-hour)exceeds half their true energy consumption (Kilowatt-hour).
How to apply forming voltage and after that how to repeat it. What is the necessity of forming voltage in RRAM.
A 3 km pipe starts from point A end at point B-Population = 3000 people
The first parallel combination is composed of a 6 ohm resistor and a 3 ohm resistor.the second parallel combination is composed of a 12 ohm resistorand a 6 ohm resistor. Draw the network and determine its equivalent resistance.
The bottom of the conduction band at one end of a silicon resistor is at the same energy level as the top of the valence band at the other end. What current flows through the resistor if the resistance is 1.12 kOhms
An emitter follower, when driven from a 10 kohm source, was found to have an output resistance Rout of 200 ohm. The output resistance increased to 300 ohm when the source resistance was increased to 20 kohm.
The quantization step size or resolution, ?, if the signal range is 5 volts;
a 4A current source is in parallel with a 30 ohme resistance, a 15 ohme resistance, and an unknown resistance, Rx. The current through the unknown resistance is 1A. Determine the value of Rx.
A material is found to have a tenth-thickness of 2.3 cm for 1.25-MeV gamma rays. (a) What is the linear attenuation coefficient for this material (b) What is the half-thickness (c) What is the mean-free-path length for 1.25 MeV photons in this materi..
An amplifier with Ri = 2 kΩ, Ro = 500Ω, and Rmoc = -107 is operated with a 1-kΩ, load. A source having a Thévenin resistance of 1kΩ and an open-circuit voltage of 2 cos(200 πt) mV is connected to the input terminals. Determine the output voltage a..
a transconductance amplifier with ri 2 komega gm 40 mav and ro 20komega is fed with a voltage source having a
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd