Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
A Capacitor is connected to a voltage source of 6V in series. A load is connected in parallel with the capacitor. The load will remain as an open circuit until 5V is put across it. The capacitor is then charged. Once the voltage across the load reaches 5V the load will no longer act as an open circuit and the capacitor will discharge. Once the load voltage has droped to 0.2 the load will act as an open circuit and the capactior will begin to charge once more.
Write an equation for the Capacitor to only discharg to 0.2V due to the load acting as an open circuit at 0.2V
Identify the bus types and the unknown variables of the power flow problem. Write the complete set of equations needed to solve the load flow problem.
a digital signal represented by a binary voltage +5.55 and -4.5V , is transmitted over an AWGN channel with noise standard dev 1.12 V.Compute the volt. f the optimum thresholdwhen the priori probabilities of the binary source
Determine the signal/noise ratio (Eb/No) in input of the receiver for each modulation format presented below if symbol error rate (SER) is required to be 10-^4 (use the coherent detection), for the solution the appropriate graphs can be used inste..
Consider the following matrix of expected profits (in units of $1K) versus potential future material price scenarios (P1 - P5), for five different designs (D1 - D5): P1 P2 P3 P4 P5 D1 10 20 30 40 50 D2 20 25 25 30 35
Sketching the Dependence of l versus h on Cartesian Axes, The distance l from a point at a height h above the Earth's surface to the horizon can be approximated using Pythagoras theorem by the expression:
What should the signal definitions be for the equations, such that the minimal about of hardware (gates) are used assuming we have an abundance of NAND gates Show the signals definitions and resulting circuitry.
the magnetic circuit shown with a mean core length of 52 cm and a cross sectional area of 18 cm^2. the length of the air gap is 0.14 cm. Determine the battery voltage required to obtain a flux density of 1.2 T in the air gap. Use the magnetization..
Three -phase motor is connected to a three-phase power source that has an abc phase sequence. the first load is a wye-connected, three-phase motor withdrawing a line current of 20A at a 0.8 lagging power factor.
Determine the relative permittivity of the dielectric, the maximum and minimum electric field intensities in medium 1 and the electric field intensity in medium 2.
What value of emitter resistor would you choose, if: a) You have to amplify the signal of a microphone that has an internal resistance of 100K using a Common Emitter bias configuration b) you have to drive a load of 50 with an Emitter Follower cir..
A PWM is to be programmed to output a signal with a pulse high width of 150 usec and a pulse low width of 250 usec. What are the values required for prescale (if any) PWMPER and PWMDTY An 8-bit configuration is used and the E-clock is 24 MHz.
A coil having 1000 turns is wrapped on ferromagnetic core constructed of sheet steel. The core has a cross-sectional area of 0.0009 m^2 and an average flux path of 30.0 cm. The core also has a length of 2 mm. The flux density in the core and airga..
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd