What is the total number of photons that will be emitted

Assignment Help Electrical Engineering
Reference no: EM13250926

A sample of hydrogen atoms are all in the n = 5 state. If all the atoms return to the ground state, how many different wavelengths will be emitted, assuming all possible transitions occur?

If there are 500 atoms in the sample and assuming that from any state all possible downward transitions are equally probably, what is the total number of photons that will be emitted when all atoms return to the ground state?

Reference no: EM13250926

Questions Cloud

Determine the speed of the muon : Consider the motion of a muon as it moves through the Earth's atmosphere. After a time ? = 2.20 e-6 s, it decays into other particles. What is the speed of the muon
Explain what change in the sound do expect to hear : if you use the sinusoidal waveform to drive the speaker: What change in the sound do you expect to hear when you increase the amplitude of the sinusoidal signal on the function generator
Explain solid mixture of sodium chloride and barium chloride : How can you calculate the quantitative precipitation of barium in a solid mixture of sodium chloride and barium chloride
Explain technique for the analysis of copper ion : Critically evaluate the procedure used in this experiment as a quantitative technique for the analysis of copper (II) ion. Suggest sources of errors and ways of minimizing the error
What is the total number of photons that will be emitted : If there are 500 atoms in the sample and assuming that from any state all possible downward transitions are equally probably, what is the total number of photons that will be emitted when all atoms return to the ground state
What is the mutual inductance of these coils : A toroidal solenoid has a mean radius of 10.0cm and a cross-sectional area of 4.8cm2 and is wound uniformly with 115 turns. What is the mutual inductance of these coils
Find the systolic blood pressure in the narrowed vein : The diameter of a blood vessel narrows by 70% due to the presence of a plaque on the blood vessel walls. what is the systolic blood pressure in the narrowed vein (in mmHg)
Write an equation for the capacitor to only discharge : Once the voltage across the load reaches 5V the load will no longer act as an open circuit and the capacitor will discharge. Once the load voltage has droped to 0.2 the load will act as an open circuit and the capactior will begin to charge once ..
What is the resulting line efficiency : The cycle time of the line is 5 minutes and the sum of all that tasks required on the line is 25 minutes. What is the resulting line's efficiency?

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Whether an fet is operating in ohmic region or active region

Discuss the operation of a JFET, including the pinch off and gate-source cutoff voltage in your explanation. Discuss how you can tell whether an FET is operating in the ohmic region or the active region.

  Determine change in resistance when the temperature rises

A platinum resistance coil has a resistance at O0 C of 100 . Determine the change in resistance that will occur when the temperature rises to 30°C if the temperature coefficient of resistance is 0.0039 K-1.

  Determine what is the new cutoff frequency

A high-pass filter with C=30pF. R= 40 kohm A) What is the cutoff frequency The output of this filter is connected to an amplifier with an input resistance of 60 kohm. B) Sketch and label the new circuit. C) What is the new cutoff frequency

  Design ac-dc voltage converter based on half-wave filtering

Design an ac-dc voltage converter based on half-wave rectification and filtering. The requirements are: 1. Choose the values of the load resistor R and the capacitor C so that the converter will have a ripple factor of 10%

  Find what is significant about the dc voltage measurements

Construct the RC differentiator. Set the channel 1 input coupling switch to dc. Next adjust the dc offset, amplitude, and frequency controls of the function generator to produce the input waveform.

  What should be the line voltage of an ac motor

An AC induction motor is rated at 900 rpm, 200V, 60HZ 3-phase. If reduce the motor speed by reducing the line frequency to 20HZ, what should be the line voltage

  How many decimal characters required to represent in decimal

How many decimal characters (including a possible minus sign) will be required to represent in decimal, sign-magnitude form numbers which are represented using twos complement 24-bit numbers in binary

  Give the solution to power factor

The solution to Power Factor, Two single-phase loads are connected in parallel across a 415 V, 50 Hz supply. One load is rated 130 kW at a power factor of 0.75

  Design simple bjt amplifier ckt for receiving hdtv signals

Design a simple BJT amplifier circuit for receiving the over-the-air HDTV signals. The circuit should have a voltage gain of 10-100, assuming your signal source (antenna) is connected to amp through a cable with an impedance of 75

  Find source vs and series resistance rs

A certain transducer is modeled with a source Vs and series resistance Rs. The voltage at its terminals is measured with a DVM having internal resistance Ri = 100 Mega ohms and is found to be 12.5 mV; adding a 5 Mega Ohms resistance in parallel

  What is the indicated temperature at the given times

A temperature sensor has a static transfer function of 0.15mV/degrees C and a time constant of 3.3 s. If a step change of 22 degress C to 50 degress C is applied at t = 0, find the output voltages at 0.5s, 2.0s, 3.3 s, and 9s.

  What is the equilibrium hole concentration

A Si sample is doped with 10^17 As atoms/cm^3. What is the equilibrium hole concentration P0 at T=300K?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd