Work and exergy destroyed during this throttling process

Assignment Help Mechanical Engineering
Reference no: EM13709144

Refrigerant-134a at 1 MPa and 100°C is throttled to a pressure of 0.8 MPa. Determine the reversible work and exergy destroyed during this throttling process. Assume the surroundings to be at 30°C.

Reference no: EM13709144

Questions Cloud

Regenerative rankine cycle with one closed feedwater heater : Water is the working fluid in an ideal regenerative Rankine cycle with one closed feedwater heater. Superheated vapor enters the turbine at 10 MPa, 480 C and the condenser pressure is 6 kPa. Steam expands through the first stage turbine where some is..
Find how long will it take the tanker starting from rest : The motion of a very massive object can be minimally affected by what would seem to be a substantial force. how long will it take the tanker, starting from rest, to reach a typical cruising speed of 6.0 m/s
Determine the current through a flashlight filament : Determine the current through a 2.9-ohms flashlight filament when connected across two 1.5-V batteries in series (a potential difference of 3.0 V)
Water is the working fluid in a rankine cycle : Water is the working fluid in a Rankine cycle. Superheated vapor enters the turbine 10MPa, 480 celcius, and the condenser pressure is 6kPa. The turbine and pump have isentropic efficiencies of 80 and 70% respectively.
Work and exergy destroyed during this throttling process : Refrigerant-134a at 1 MPa and 100°C is throttled to a pressure of 0.8 MPa. Determine the reversible work and exergy destroyed during this throttling process. Assume the surroundings to be at 30°C.
What will the acceleration be if the force is halved : A constant force is applied to an object, causing the object to accelerate at 10 m/s2. What will the acceleration be if the force is halved
What is the total resistance of the circuit : Three 35-(Ohms) light bulbs and three 70-(Ohms) light bulbs are connected in parallel. What is the total resistance of the circuit
Find the angle between direction of its motion and x-axis : A butterfly moves with a speed of v = 12.0 m/s. the y-components of its velocity is 8.00m/s. Find the angle between the direction of its motion and the x-axis
How fast will he be going when his feet touch the ground : A fireman starts from rest with his feet 18.0 ft above the ground and slides down a pole with a downward acceleration of 10.0 ft/s2. How fast will he be going when his feet touch the ground

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Combustion in a cylinder causes the pressure to increase

Combustion in a cylinder causes the pressure to increase, which moves the piston a distance (x) of 7 inches. The piston is held in place by a spring ( k=60lbfin) that was at its relaxed length before the combustion process. How much work did the expa..

  Central heating system is to circulate air through the ducts

The 60W fan of a central heating system is to circulate air through the ducts. The analysis of the flow shows that the fan needs to raise the pressure of the air by 50Pa to maintain flow. The fan is located in a horizontal flow section whose diameter..

  How much work must the motor do to stop the body when the

a robot arm is lifting a large body. the mass of the body is 4.66 slugs its radius of gyration is .6667 ft and its

  Determine the angular velocity

Determine the angular velocity of the two 10-kg rods in Fig. 2 when , if they are released from rest in the position . Neglect friction.

  Determine be naturak frequency of the system

A 0,5Kg mass attached linear spring suffress 01 N/m. Determine be naturak frequency of the system in hortz e reapert this calculation for a mass of 50Kg and a suffress of 10N/m and compare your result to that of part.

  The iron casting and the water are allowed to come to

an 8-kg iron casting at 550 degc is quenched in a tank containing 0.03 m3 of liquid water initially at a temperature of

  Determine mud height at which blocks will overcome friction

Mud is stopped using a wall made from 1.2 m high x 0.25 m wide rectangular concrete blocks as shown in figure below. Blocks density is 2700 kg/m3, mud density is 1800 kg/m3, and friction coefficient between ground and concrete blocks is f = 0.3.

  Fifty five kj of heat is transferred to the air during this

two kg of air is contained in a piston-cylinder assembly. the initial volume is 0.01m3 and pressure is 10 bar. the air

  Determine the maximum power supplied by the engine

A sports car has a mass of 2000 kg and an engine running at an efficiency of 0.63, as it moves forward with a constant velocity of v=50 m/s,the wind creates a drag resistance on the car of FD=1.2v^ newtons. Determine the maximum power supplied by the..

  A pressure cooker closed tank contains water at 200 f with

a pressure cooker closed tank contains water at 200 f with the liquid volume being 110 of the vapor volume. it is

  Calculate the maximum power kw that could be developed by

a site near an ocean is being evaluated for power generation using wind turbine. the site is observed to have steady

  A ship travels 40km on course of 17 degree south of east

a ship travels 40km. on course of 17 degree south of east and then travels 90km. on course 50degree west of south. find

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd