Will water bubble into the vapor phase under these

Assignment Help Civil Engineering
Reference no: EM13562650

1.There are two .25 m long concentric cylinders in a viscometer. Only the inner cylinder is rotating. THe velocity distribution is given by V(r)=1000r-0.4/r [m/s]. If the diameters of the cylinders are 3 cm and 5 cm, respectively, what is the fluid viscosity if the torque on the inner cylinder is measured to be 0.0026 Nm?

2.A student in the laboratory plans to exert a vacuum in the head space above a surface of water in a closed tank. She plans for the the absolute pressure in the tank to be 10,400 Pa. The temperature in the lab is 20°C. Will water bubble into the vapor phase under these circumstances?

Reference no: EM13562650

Questions Cloud

What is the velocity of an electron that falls through : What is the velocity of an electron that falls through a magnetic field aligned electric potential of volts across an accelertion region that is 10 k long? (neglect collisions and gravity and assume the electron has zero degree pitch-angle (i.s movin..
Determine the direction of the resultant force measured : The driver of a car traveling up a 2% grade at an initial speed of Vo applied the brakes abruptly and the vehicle slid to a complete stop at an average deceleration of 8ft/s^s. Was the pavement wet or dry?
Determine the normal strain in each bar : The two bars shown in the figure are used to support a load P. When unloaded, joint B has coordinates (0, 0). After load P is applied, joint B moves to the coordinate position (0.35 in., -0.60 in.). Assume a = 11 ft, b = 6 ft, and h = 8 ft. Determine..
How much work must be done to move a chair : How much work must be done to move a 3.8 kg chair 6.1 m acrossthe floor at constant velocity if the coefficient of kineticfriction between the chair and the floor is 0.64
Will water bubble into the vapor phase under these : A student in the laboratory plans to exert a vacuum in the head space above a surface of water in a closed tank. She plans for the the absolute pressure in the tank to be 10,400 Pa. The temperature in the lab is 20°C. Will water bubble into the vapor..
What is the maximum amount of cargo : A small truck is to be driven down a 4% grade at 70mi/hr. The coefficient of road adhesion is 0.95, and it is known that the baking efficiency is 80% when the truck is empty and decreases by one percentage point for every 100 lb of cargo added. Ignor..
What is the maximum weight wmax of the crate that the system : Rope BCA passes through a pulley at point C and supports a crate at point A. Rope segment CD supports the pulley and is attached to an eye anchor embedded in a wall. Rope segment BC creates an angle of
Channel is designed to carry a discharge : A 10-feet trapezoidal channel is designed to carry a discharge of 1,000cfs with side slopes: Z1 = 4 and Z2 = 5.  The channel bed slope is 0.04 ff/ft and has Manning's N of 0.03. To protect the channel from erosion
Obtain the change in the entropy of the water : A freezer is used to freeze 3.0 Lof water completely into ice. The water and the freezer remain at aconstant temperature of T = 0°C. Determine the change in the entropy of the water

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine what constricted width would be to force the flow

Given that uniform flow is subcritcal and there is a constriction in a rectangular channel, how do you determine what the constricted width would be to force the flow to be critical. Draw this transition on a specific energy curve.

  What would the new value of hc be

If the fracture were planar in shape, having an average opening of 2 mm, what would the new value of Hc be?

  What is the energy loss in the basin with and without blocks

If the river depth is larger than the subcritical sequent depth, a submerged hydraulic jump forms. Sometimes, concrete blocks called "baffle blocks" are placed on the stilling basin floor to help the hydraulic jump form within the basin.

  What is the discharge from the pipe

Flow occur  throught a sand-filled pipe with a cross-sectional area of 60 cm^2. If K is 10^-3 cm/s and the gradient is 0.01, what is the discharge from the pipe ?

  Determine the forces fx and fy necessary to hold the pipe

Water flows steadily through a horizontal 30 degree upward bend. The inlet diameter is 0.3 m, the velocity is 12 m/s, and the pressure is 128 kpa gage. The outlet diameter is 0.38 m and the pressure is 145 kpa gage.

  Estimate cu value at a and b after clay layer consolidated

two isotropically consolidated undrained (ciu) triaxial tests, CU1 triaxial tests, CU1 and CU2, were conducted on a normally consolidated (Nc) clay under effective consolidation stresses of 100 and 200 kPa respectively.

  Determine the velocity of the collar at point b for values

To imagine the diagram, the collar at point A (unstretched) is on the same x-axis as the anchor @ C, while the collar point B (stretched) is located downwards-left to point A, forming a 30 degree angle with the y-axis (vertical). In other words, the ..

  What is the biomass concentration in the aeration tank

average flow rate = .0022 m^3 /s (190 m^3 /d) Influent Substrate concentration = 250 mg/L as COD (all essentially soluble) Mean cell residence time is to be 5 days Volume of mix tank = 25 m^3 the reactors kenetic constants are

  Determine the position where the net electric field is zero

Given that the seperation distance between the charges is 5m, q1 = -3q2, find the position where the net electric field is zero. Do not use infinity.

  Determine the lrfd nominal and adjusted design values

Problem: Determine the LRFD nominal and adjusted design values and adjusted design resistances for the following members and loading combinations. All members are Select Structural Southern Pine and are fully braced to prevent lateral torsional bucki..

  Estimate cross sectional dimension of bar under strain

A 1000 in diameter solid steel (p= 0.303) bar is 10.0 ft long. Under a tensile load. (a) Estimate the lateral strain experienced by the bar (b) Estimate the cross sectional dimension of the bar when under strain

  What is the maximum positive coordinate reached by particle

The position of a particle moving along an x axis is given by x = 17t2 - 5.0t3, where x is in meters and t is in seconds. (a) Determine the position, velocity, and acceleration of the particle at t = 3.0 s. x = m v = m/s a = m/s2

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd