Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
1.According to the National Design Specification for Wood Construction (NDS), the tension PARALLEL to the grain, Ft, is less than the compression PARALLEL to the grain, Fc, why?
Will promptly rate any acceptable response as a life saver.
2.Write a brief description (1-3 paragraphs) of the Saint Venant equations (words only, no equations) comparing them to the Navier-Stokes equations, emphasizing the ASSUMPTIONS on which they are based.
A machine is supported on four steel springs for which damping can be neglected. The natural frequency of vertical vibration of the machine-spring system is 200 cycles per minute. The machine generates a vertical force p(t)=p0sinwt.
A brass alloy has a yield strength of 280 MPa, a tensile strength of 390 MPa, and an elastic modulus of 105 GPa. A cylindrical specimen of this alloy 12.7 mm in diameter and 250 mm long is stressed in tension and found to elongate 7.6 mm
Tank A has a volume of 100 liters and contains saturated vapor r-134 at 30C. With the valve open slightly flow enters cylinder B. a pressure of 200kpa is required to lift piston in b. the process ends when the pressue at A drops to 200kPa.
Determine an appropriate pipe diameter and slope for this reach, and establish the pipe invert elevations at the upper and lower manholes. Assume that a minimum earth cover of 2 m above the pipe crown is required.
Select the number and size of reinforcing bars required to resist a total factored moment of 180 ft. kips for a rectangular section with b = 12 in., d = 19.5 in., h = 24 in., fc = 4 ksi, and fy = 60 ksi. Check for minimum reinforcement requirement..
Calculate the percentage of change in total volume with respect to its initial volume when a specimen of this clay is completely dried from a water content of 80%. Assume that the clay remains saturated from liquid limit to shrinkage limit.
The velocity out of the tube may be approximated by V = √(2(p-patm)/ρ), where p is the absolute tank pressure. Determine the time at which the pressure (gage) in the tank is 20 kPa if the initial pressure is 40 kPa (gage)
A 100-ft steel tape was used in the field to measure a distance of 247.53 ft. the following data represents the conditions in the field at the time of measurement: tempreture = 41 F, tension = 30 ib, and tape supported at ends only.
A 1400-ft-long sag vertical curve (equal tangent)has a PVC at station 115 + 00 and elevation 750 ft. The initial grade is -3.5% and the final grade is +6.5%. Determine the elevation and stationing of the low point, PVI, and PVT
an elevator drive sheave of diameter 1 m and negligible mass is mounted on a shaft midwaynbspbetween bearings which are
the block is fitted between the fixed supports. if the glued joint can resist a maximum shear stress of T(allow)=2ksi, determine the temperature rise that will cause the joint to fail. Take E= 10(10^3)ksi, v=0.2
Determine how many buses needed to provide service on the following route with the indicated characteristics: -Route length: 16 miles (one way) -Headway: 15 minutes -Average number of stops made during run, one direction: 22
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd