When the pressure drops across the basket strainer

Assignment Help Civil Engineering
Reference no: EM13540163

Abasket strainer is installed in a 15-cm diameter pipe. Pressuregauges are installed immediately upstream and downstream of thebasket strainer. When water flows at 100 m3/hr, the pressure gaugeimmediately upstream of the basket strainer measures 1 bar.

a. When the basket strainer is clean, the pressure immediatelydownstream measures 0.9 bar. Calculate the local loss coefficientof the clean basket strainer.

b. When the pressure drops across the basket strainer by half(i.e., to 0.5 bar after the strainer)at the 100 m3/hr flow rate, itis removed for cleaning. What is the local loss coefficient of thebasket strainer at this point?

Reference no: EM13540163

Questions Cloud

A jar test has shown that the optimum dose : A jar test has shown that the optimum dose of ferric chlorideconsumes all of the alkalinity. If the amount of the ferricchloride that is in excess is 10 mg/l, how much lime(Ca(OH)2) in mg/l must be added to neutralize the acidformed.
Show the combined state of stress on the surface : Determine the maximum shearing stress and any coexisting normalstress on the element and show these on a correctly orientedelement.
A developer has requested permission to build a large retail : A developer has requested permission to build a large retail store at a location adjacent to the intersection of an undivided four-lane major road and a two-lane minor road.
What is the velocity of flow in this point : A combined pitot static tube has a coefficient of 0.98. Thedifferential head reading is 0.874m of water when it is positionedon the centreline of a pipe of constant diameter.
When the pressure drops across the basket strainer : Abasket strainer is installed in a 15-cm diameter pipe. Pressuregauges are installed immediately upstream and downstream of thebasket strainer. When water flows at 100 m3/hr, the pressure gaugeimmediately upstream of the basket strainer measures 1 ba..
Determine the maximum bending stress in the strap : An L2 steel strap having a thickness of 0.125 in. and a widthof 2 in. is bent into a circular arc of radius 600 in. Determine the maximum bending stress in the strap.
Estimate the maximum outlet velocity that this system could : A mining engineer plans to do hydraulic mining with a high-speedjet of water. a lake is located H=300 m above the mine site Waterwill be delivered through L=900 m of hte fire house with an inside diameter D
What is the specific discharge in this rectangular channel : A large concrete channel holds a hydraulic jump in which the subcritical depth of flow is 2.5 m.  If 40 percent of the specific energy in the flow is lost through the hydraulic jump, what is the specific discharge in this rectangular channel?
Determine the specifications unstretched length and spring : Determine the specifications (unstretched length and springconstant k) for the elastic cord to be used at a bungee-jumpingfacility. Participants are to jump from a platform 150 ft above the ground. When they rebound, they must avoid an obstacle that ..

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine rate of production of final product nd composition

An ethanol plant distills alcohol from corn. The distiller processes 2.0 t/h of feed containing 15% alcohol and 82% water; the rest is inert material. The bottoms (waste) produced is 85% of feed and contains 94% water, 3.5% alcohol, and 2.5% inert..

  Calculate the maximum shear and indicate in terms of x

a. Determine the shear and moment diagram. b. Calculate the maximum normal stress on the top of the beam, on the bottom of the beam and indicate in terms of x its location.

  Uva levels in raw and treated drinking water

My question is regarding UVA levels in raw and treated drinking water with regard to TOC and DOC removal. Is there a jar test procedure that incorporates the UVA values of the various stages of treatment and is there a document you could refer me ..

  Determine what force p is required to hold the gate in place

The air above the liquid is under a pressure of 5 psig, and the specific gravity of the liquid in the tank is 0.80. If the rectangular gate is 6 ft wide and if y1 = 1 ft and y2 = 10 ft, what force P is required to hold the gate in place

  Determine the angle theta which the 6-lb

uniform rod makes with the vertical during the roll, and (b) the speed of the roller after it moves 4 ft., starting from rest. The roller rolls without slipping, and the rod hangs vertically (theta = 0) when the system is at rest.

  Find probability that specimen will contain detectable level

The article "Leachate from Land Disposal Residential Construction Waste" (authored by W.J. Weber, Y.-C Jang, T.G. Townsend, and S. Laux, Journal of Environmental Engineering, 128(3): 237 - 245, 2002) presents a study on contamination

  Determine flow rate into or out of each reservoir

Three reservoirs are connected by three pipes with hA = 100 f t, hB = 20 f t, hC = 0 f t, l1 = 1000 f t, l2 = 500 f t, l3 = 400 f t and D1 = D2 = D3 = 1 f t. Determine flow rate into or out of each reservoir if friction in each pipe is 0.02.

  Find out velocity head expressed in atmospheres

What is the velocity head expressed in atmospheres for a rapid filter operated at a surface loading rate of 475 m/d when the local porosity is 0.40?

  Determine the time for the log to reach a speed

A truck is hauling a 300-kg log out of a ditch (20 degree incline) using a winch attached to the back of the truck. Knowing the winch applies a constant force of 2500N and the coefficient of kinetic friction between the ground and the log is 0.45

  How to label turing points numerically starting with tp1

A differential leveling loop started and closed on BM Juno, elevation 5194.02 ft. The BS and FS distancces were kept approximately equal. Readings (in ft) listed in the order takken are 9.65, 2.11, 2.51, 8.35, 2.06, 9.25, 7.93, 2.83, 5.05, and 4.6..

  Compute original length if deformation is totally elastic

A cylindrical specimen of a metal alloy is stressed in compression. if its original and final diameters are 40.00mm and 40.10mm respectively, and its final length is 120.00mm, compute its original length (L1) if the deformation is totally elastic.

  Find the maximum load the suction cup can support

A suction device is being designed based on the venturi principle to lift objucts submerged in water. The operating water temperature is 50 C.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd