User Account

All Pages

When the input is 100 kpa the output is 5 mv and when the

Assignment Help Mechanical Engineering
Reference no: EM13612277

A pressure sensing device has an electrical output and is approximately linear. When the input is 100 kPa, the output is 5 mV and when the input is 1000 kPa, the output is 125 mV. What is the sensitivity of this device?

Reference no: EM13612277

Questions Cloud

After the rcs thruster is turned off find a the magnitude : a space vehicle is coasting at a constant velocity of 15.7 ms in the y direction relative to a space station. the pilot
Determine a the quality of steam in the tank at the initial : a rigid tank contains 7.5 kg of saturated water mixture at 400 kpa. a valve at the bottom of the tank is now opened and
Partners flip and flop have capital balances in a : partners flip and flop have capital balances in a partnership of 80000 and 120000 respectively. they agree to share
Flip earns a salary of 7500 per month during the year fica : flip earns a salary of 7500 per month during the year. fica taxes are 8 on the first 100000 of gross earnings. federal
When the input is 100 kpa the output is 5 mv and when the : a pressure sensing device has an electrical output and is approximately linear. when the input is 100 kpa the output is
Prepare the journal entry on august 31 to record the final : the red white amp blue partnership was begun with investments by the partners as follows red 175000 white 220000 and
It rises to its maximum height and then falls down to the : a golfer hits a shot to a green that is elevated 3.20 m above the point where the ball is struck. the ball leaves the
Fit a logistic regression model to these data is the model : a study was performed to investigate the relationship betwee family income and ownership of a luxury car. 16 households
The atomic weight of copper is 635 gmol calculate its : the atomic weight of copper is 63.5 gmol. calculate its theoretical density given that it has fcc crystal structure and

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  A plate fin heat exchanger for truck is designed to cool

a plate fin heat exchanger for truck is designed to cool high temperature and high pressure oil using high pressure

  Draw the shear and moment diagrams for the beam

the traveling crane consists of a 5-m-long beam having a uniform mass per unit length of 20kg/m. The chain hoist and its supported load exert a force of 8 kN on the beam when x=2m. draw the shear and moment diagrams for the beam.

  What thickness of extruded polystyrene sheet must be

a new building to be located in a cold climate is being designed with a basement that has an l 200-mm-thick wall. inner

  Determine the minimum coefficient of static friction

Determine the minimum coefficient of static friction between the crate and the truck so that the crate does not slide relative to the truck.

  Determine the minimum value to create the specified moment

a 960 N.m moment is required to straghten a post. if the capacity of a winch puller is 2400N, determine the minimum value to create the specified moment.

  Design a packed tower for the absorption so2 from air the

design a packed tower for the absorption so2 from air. the so2 feed contain 0.0016 mol frac a into pure water in column

  List the compressibility factors for air nitrogen oxygen

air is made up of nitrogen oxygen carbon dioxide argon water vapor and some other stuff in really small amounts. list

  When the vessel is under 9 psi of vacuum the height of the

a u-tube manometer is used to measure the pressure of a vessel under vacuum. assume the manometer is open to

  Draw the projections of rod showing curves of intersection

A connection of rod of 50 mm diameter has a rectangular block 50 mm wide and 25mm thick forged at its end. A turned radius of 25 mm joins the rod and the block. Draw the projections of the rod showing curves of intersection.

  Air enters the compressor of an air-standard brayton cycle

air enters the compressor of an air-standard brayton cycle at 100kpa 300k with anbspvolumetric flow rate of 5m3s. the

  Determine the outlet temperature of the hot fluid

Determine the outlet temperature of the hot fluid.

  Calculate the mass of mixture produced at the mixing stage

calculate the mass of mixture produced at the mixing stage, the mass jam produced from the kettle and the mass od water evaporated from the kettle.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd