Determine a the quality of steam in the tank at the initial

Assignment Help Mechanical Engineering
Reference no: EM13612280

A rigid tank contains 7.5 kg of saturated water mixture at 400 kPa. A valve at the bottom of the tank is now opened and liquid is with drawn from the tank. Heat is transferred to the steam such that the pressure inside the tank remains constant. The valve is closed when no liquid is left in the tank. If it is estimated that a total of 5 kJ of heat is transferred to the tank, determine (a) the quality of steam in the tank at the initial state, (b) the amount of mass that has escaped, and (c) the entropy generation during this process if heat is supplied to the tank from a source at 500°C.

Reference no: EM13612280

Questions Cloud

The rocket attains its launch speed in a negligibly short : a rocket is fired at a speed of 72.0 ms from ground level at an angle of 50.0 deg above the horizontal. the rocket is
Hazard company is considering the acquisition of a machine : hazard company is considering the acquisition of a machine that costs 375000. the machine is expected to have a useful
The mass of the piston is such that it takes 03mpa of : consider a piston-cylinder device that contains 0.5m3 of saturated water vapor at 0.2mpa and where the piston initially
After the rcs thruster is turned off find a the magnitude : a space vehicle is coasting at a constant velocity of 15.7 ms in the y direction relative to a space station. the pilot
Determine a the quality of steam in the tank at the initial : a rigid tank contains 7.5 kg of saturated water mixture at 400 kpa. a valve at the bottom of the tank is now opened and
Partners flip and flop have capital balances in a : partners flip and flop have capital balances in a partnership of 80000 and 120000 respectively. they agree to share
Flip earns a salary of 7500 per month during the year fica : flip earns a salary of 7500 per month during the year. fica taxes are 8 on the first 100000 of gross earnings. federal
When the input is 100 kpa the output is 5 mv and when the : a pressure sensing device has an electrical output and is approximately linear. when the input is 100 kpa the output is
Prepare the journal entry on august 31 to record the final : the red white amp blue partnership was begun with investments by the partners as follows red 175000 white 220000 and

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  What is the percent increase in the air velocity

If the room temperature is 15C and the temperature of the air exiting the hair dryer is 50C, what is the percent increase in the air velocity as it passes through the dryer.

  A levitation fan has been selected that delivers this

a hovercraft has a square planform a mass of 1.8 kg and has a plenum pressure requirement of 125 pa. a levitation fan

  Consider 20 kg of a 996 wt fe-04 wt c alloy that is cooled

consider 2.0 kg of a 99.6 wt fe-0.4 wt c alloy that is cooled to a temperature just below the eutectoid. a how many

  1 compare liquids and gases with regard to theirbull

1. compare liquids and gases with regard to theirbull shapebull volume occupiedbull densitybull viscositybull

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Determine the mass fractions of alpha and beta phases

Determine the mass fractions of alpha and beta phases, Determine the mass fractions of primary beta and eutectic microconstituents, Determine the mass fraction of eutectic beta

  Determine the bolt stiffness

Determine the bolt stiffness, the tube stiffness, and the joint constant C.

  The velocity of the air stream decreases from 230 ms to 30

nitrogen gas at 60 kpa and 7 degrees celsius enter an adiabatic diffuser steadily with a velocity of 195 ms and leaves

  Determine the maximum torque t

a shaft is made of a steel alloy having an allowable shear stress of 12 ksi. If the diameter of the shaft is 1.5 in., determine the maximum torque T that can be transmitted. What would be the maximum torque T' if a 1 in. diameter hole is bored thr..

  Determine the horizontal line along

Determine (a) the horizontal line along which the shearing stress is a maximum, (b) the constant k in the following expression for the maximum shearing stress.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Plot wind speed against height on linear

for a neutral surface layer, plot wind speed against height on linear and on semi-log graphs for friction velocity of .5 m/sec and aerodynamic roughness length.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd