What would the gram molecular weight of a gas of 1.0 micron

Assignment Help Civil Engineering
Reference no: EM13559138

1.In a hydrometer test , the results are as follows:Gs =2.60 , temperature of water=24c ,and R=43at 60 min after the start of sedimentation (see figure 2.24 ) . what is the diameter , D, of the smallest -size particles that have settled beyond the zone of measurement at that time(that is , t=60 min)?

2.If aerosol particles were considered to be extremely large gas molecules, what would the gram molecular weight of a gas of 1.0 micron diameter particles having a density of 1000 kg/cubic meter.

Reference no: EM13559138

Questions Cloud

What is the net work done by the system : A thermodynamic system is taken from state A to state B tostate C, and then back to A. What is the net work done by the system as it moves once through the cycle ABCA
An old wooden telephone pole with a single cross member was : An old wooden telephone pole with a single cross member was blown off center during a recent storm. To temporarily stabilize the telephone pole, a repair crew has attached a cable from the end of the cross member to an eye-ring stake anchored in the ..
Determine the original temperature of the cylinder : A 150g copper bowl contains 220 g of water, both at 20.0degrees C. A very hot 300g copper cylinder is dropped intothe water, What is the original temperature of the cylinder
A general description : A general description
What would the gram molecular weight of a gas of 1.0 micron : If aerosol particles were considered to be extremely large gas molecules, what would the gram molecular weight of a gas of 1.0 micron diameter particles having a density of 1000 kg/cubic meter.
Estimate what is the density of the life jacket : A 73.7-kg person puts on a life jacket, jumps into the water, andfloats. What is the density of the life jacket
Virtual organization differ from more traditional approaches : How do these planning activities in a virtual organization differ from more traditional approaches?
Determine the volume of irrigation water needed in ac-ft : A certain crop has a consumptive use requirement of 1.2 ac-ft of water per acre of crop land. The crop is planted on 780 acres of land. Precipitation falling during the growing season is 3.2 inches. The remainder of the 1.2 ac-ft /ac
Calculate the acceleration of the seed : A record turntable is rotating at 33 1/3 rev/min. A watermelonseed is on the turntable 6.5 cm fromthe axis of rotation. Calculate the acceleration of the seed, assumingthat it does not slip

Reviews

Write a Review

Civil Engineering Questions & Answers

  What is the minimum perimeter of that the blade must have

A rectangular blade weighing 0.02 lbf is kept in the surface of water (sigma=0.073 N/m) solely by surface tension forces. What is the minimum perimeter of that the blade must have so that this is possible

  What is the rolling resistance of the loaded unit

Estimated rolling resistance factor the haul road is 3000 lb/ton.  If the scraper weighs 35,000 lb (empty) and carries 25 loose cubic yards per trip.  What is the rolling resistance of the loaded unit?

  Calculate an estimate of the friction coefficient of steel

A fellow I know wanted to know the coefficient of friction between steel and commercial carpet. The value was not in the tables of any textbook he had, so he devised an experiment.

  Calculate the true stress for fracture in the neck region

A copper wire breaks under an engineering stress of 43x10^3 psi. Its ductility is 77%it reduction area. Calculate the true stress (in psi) for fracture in the neck region.

  Establish a grass cover over a 10ha landfill the root zone

establish a grass cover over a 10ha landfill. the root zone of the grass is 40cm deep. increase the volumetric water

  Determine the diameter of the pipe required to convey

Water at 20 °C is transported through a 200 m long wrought iron pipe with a head loss of 9.8 m. Determine the diameter of the pipe required to convey 10L/sec.

  Calculate the max tension min tension and the total length

A rectangular channel carries discharge of 10 m^2/s per unit width, with a sluice gate. Calculate the flow depth y3, if a hydraulic jump forms downstream of the sluice gate when y1 = 20 m.

  Determine the maximum water hammer pressure if the initial

A 1000 ft long steel pipe carries water from a reservoir with a water elevation at 826 ft. The pipe has a diameter of 12 in. with a wall thickness of .5 in. A gate valve at the downstream end is slowly closed during a half-mintue period

  Determine the discharge in the channel in m

A very long rectangular channel connects two reservoirs and has a longitudinal slope of 0.005. The channel has a width of 10 m and a Manning’s n of 0.030.

  Ethics code and professional conduct specific issues

specific issues that are important to create code of ethics and professional

  Plot the specific energy diagram for depths ranging

A rectangular concrete channel (n=0.015, S_o = 0.005) has a bottom width of 6.0 m and a discharge rate of 25 m^3/s. 1) Compute the normal depth y_n 2) Compute the critical depth y_c 3) Compute the minimum specific energy E_min

  Explain how to change the cell phone service

Plan 2 has a $40/month access fee, unlimited nights and weekends, 750 anytime minutes plus $0.29/minute for minutes over 750, text messages cost $0.05 each, and roaming cost $0.39/minute whenever she leaves the state.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd