What would be the new minimum downstream do

Assignment Help Civil Engineering
Reference no: EM13319462

A single source of BOD causes an oxygen sag curve with a minimum downstream DO equal to 6.0 mg/L. If the BOD of the waste is doubled (without increasing the waste flow rate), what would be the new minimum downstream DO? In both cases assume that the initial oxygen deficit just below the source is zero and the saturated value of DO is 10 mg/L. (Note that when the initial deficit is zero, the deficit at any point is proportional to the initial BOD)

Reference no: EM13319462

Questions Cloud

A nation with fixed quantities of resources is able : Does the principle of “increasing opportunity cost” hold in this nation? Explain briefly. (Hint:What happens to the opportunity cost of bread—measured in number of ovens—as bread production increases?)
Devlop operations strategy : Analyze the relative strengths and weaknesses of the different perspectives for developing operations strategy you have examined this week and if asked to choose one approach to follow, which would you select and why?
Compute how many grams of o2 produced from heating kclo3 : Small quantities of oxygen can be prepared in the lab by heating potassium chlorate, KCIO3(s) 2KClO3 -> 2KCl+3O2 Calculate how many grams of O2(g) can be produced from heating 59.4g of KClO3(s)
A number of countries working together to build a space : As long as all resources are fully employed and every firm in the economy is producing its output using the best available technology, the result will be efficient.”Do you agree or disagree with this statement? Explain your answer.
What would be the new minimum downstream do : A single source of BOD causes an oxygen sag curve with a minimum downstream DO equal to 6.0 mg/L. If the BOD of the waste is doubled (without increasing the waste flow rate), what would be the new minimum downstream DO
Normative ethical relativism : Normative ethical relativism
At what rate must pac be added to meet the proposed standard : A municipal drinking water treatment plant discovers that it has an unacceptably high level of the pesticide carbofuran and must develop a treatment technique to reduce the concentration to satisfy the relevant water quality standard.
Compute the osmotic pressure of a saturated aqueous solution : The solubility product Ksp for silver iodide is 1.5X10%u221216 at 298K. calculate the osmotic pressure of a saturated aqueous solution of silver iodide at this temp. you may assume that the solution behaves ideally.
The federal reserve announces it is increasing the discount : Explain whether each of the following is an example of a macroeconomic concern or a microeconomic concern.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Calculate value of temperature that can increase efficiency

An engineering student, recognizing that the "ideal gas law" requires gas velocity to be function of temperature, suggests that an easy way to increase efficiency would be to change the temperature of the exhaust gas being treated.

  Determine the relevant pi groups

The break up of a liquid jet into droplets of diameter d depends on the jet diameter D, the jet velocity V, viscosity Mu, density rho,and surface tension sigma.

  Determine the fine grains of low plasticity

Soil A is micaceous with an average grain relative density of 2.80, and has a high plasticity in its fine fraction. The ground quartz-feldspathic B is, with an average relative density of 2.65 and fine grains of low plasticity.

  Estimate the buoyant force on deep balsa raft

Estimate the buoyant force on 10'x10' by 2' deep balsa (SG=0.2) raft with you in it. How deep is it in the water. Be sure to draw well leveled schematic of the system.

  Determine the minimum length of curve that can be designed

you are designing a highway to AASHTO guidelines on rolling terrain where the design speed will be 65 mi/hr. At one section, a +1.25% grade and a -2.25% grade must be connected with and equal tangent vertical curve.

  What maximum load can be applied tot the center of the beam

A simply supported steel 'I beam' is made of three 1"*8" plates with a mass of 898.4 lbmass each as shown in I beam form. Steel has a modulus of elasticity of 30*10^6 psi. The beam is allowed to deflect 1.05 inch.

  Determine the magnitude and direction of the resultant force

determine the magnitude of the resultant force and its direction, measured counterclockwise from the positive axis. The other force is F=700N with a 15 degree angle to the x-axis.

  Determine the back emf when giving an output

A 440 -V shunt motor has armature resistance of 0.8 ohm and field resistance of 200 ohm . determine the back emf when giving an output of 7.64 KW at 85% efficiency

  Determine the maximum permissible torque tmax

The composite shaft is made of a steel sleeve, which is bonded to a brass core. The outer diameters of the two parts are d1 = 40 mm for the brass core and d2 = 50 mm for the steel sleeve.

  Explain what is the ph value of water containing

What is the pH value of water containing 0.005 M of an acid with a acid dissociation constant of 0.001 M. The dissociation of the acid in water can be represented as: HA H+ + A-

  Determining maximum acceleration and maximum velocity

The posItIon of a particle along a straight line is given by s = (t 3 - 9t 2 + 1St) ft, where t is in seconds. Determine its maximum acceleration and maximum velocity during the time interval 0 :5: t :5: 10 s.

  What nominal and effective rates of return per year

A 12%,$ 50,000 bond is offered for sale at $45,000. If bond interest is payable monthly and the bond matures in 20 years, what nominal and effective rates of return per year will the purchaser make on the investment

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd