### What would be the co concentration in the box

Assignment Help Civil Engineering
##### Reference no: EM13544498

GIVEN: A simple way to model air pollution over a city is with a box model that assumes complete mixing and limited capability for the pollution to disperse horizontally or vertically except in the direction of the prevailing winds (for example, a town located in a valley with an inversion layer above it). Consider a town having an inversion at 250 m, a 20-km horizontal distance perpendicular to the wind, a windspeed of 2 m/s, and a carbon monoxide (CO) emission rate of 60 kg/s .Assume the CO is conservative and completely mixed in the box.

FIND: What would be the CO concentration in the box?

### Write a Review

#### Dimensions of symmetrical trapezoid plate

The plate is submerged in a liquid is a vertical position with the parallel sides horizontal and the shorter parallel side at the top and exactly in the surface of the liquid.

#### Determine the horizontal components of the forces necessary

The pressure at the end of the bend is 78 pounds per square inch. Determine the horizontal components of the forces necessary to hold the bend in place.

#### For what reason would need to use darcys law in foeld

FOR WHAT REASON WOULD YOU NEED TO USE DARCY'S LAW IN THE FOELD RATHER THAN IN THE LABORATORY

#### Determine what is the coefficient of permeability

An aquifer is 45 meters deep and has a well that pumps water at 850 cubic meters per day. One observation well is located 45 meters away and has a water surface that is 44.35 meters above the bottom of the aquifer.

#### Determine the load p if the total elongation of the system

A 0.25 in diameter copper rod BC is securely attached between two identical 1 in diameter steel rods (AB and CD). Find the load P if the total elongation of the system is measured to be 0.0312 in. Esteel= 29,000ksi, Ecopper=17,000ksi.

#### Find how many assemblies the inspector may inspect per min

A grievance has been filed by the union at Dorben Co. regarding the final inspection station, in which the operator slightly lifts a 20 lb assembly, examines all sides, and, if acceptable, sets it back down on the conveyor, where the assembly goes..

#### Prove that the forces are equal and that the lines of action

this cuts it down to a single force that you have to solve for, regardless of what type of member it is. Prove that the forces are equal and that the lines of action are along an angle theta. HINT: Use to do equations of equilibrium.

#### Design a curve for the highway by computing the radius

The PI is at station 250+50, the design speed is 65mi/h, and a maximum superelevation of 0.07 ft/ft is to be used. If the central angle of the curve is 38 degrees, design a curve for the highway by computing the radius and stationing of PC and PT.

#### Explain how transformation affects drawing of scatterplot

a. Use algebra and linearity of the expectation operator to find the answer. b. Explain how the transformation affects the drawing of the scatterplot we used to develop our understanding of covariance, and therefore why the answer to part a. shoul..

#### Determine the spiral curve length to satisfy all requirement

A horizontal curve on a two-lane highway is designed with a 818.51ft radius, 12ft lane, superelevation 6.4%, and a 50mph design speed. Deflection angle is 90 degree. The maximum relative gradient is 0.50.

#### Determine the speed with which b must walk toward a

Swimmer A immediately starts walking toward B at a speed of 2ft/s relative to the raft. Knowing that the raft weighs 300 lb, determine (a) the speed of the raft if B does not move, (b) the speed with which B must walk toward A

#### Design rectangular sections for beams-loads and values given

fy=50000psi, f'c=3000 span of l=28 ft, dead load not including beam weight = 3 k/ft, live load=3 k/ft, p*=0.5pb, concrete weights=150 lb/ft cubed, use h=d+2.5 inch, assume beam weight =10kN/m and phi=0.90