What will the cars maximum acceleration rate be under these

Assignment Help Civil Engineering
Reference no: EM13563867

A 3000-lb car is traveling on a paved road with Cd (coefficient of drag) = 0.35, Af (frontal area of the vehicle) = 21ft^2, and p(air density)=0.002378 slugs/ft^3. Its engine is running at 3000rpm and is producing 250ft-lb of torque. The car's gear reduction ratio is 3.5 to 1, driveline efficiency is 90%, driveline slippage is 3.5%, and the road-wheel radius is 15 inches. What will the car's maximum acceleration rate be under these conditions on a level road? (Assume that the avilable tractive effort is the engine-generated tractive effort.)

Reference no: EM13563867

Questions Cloud

Determine the maximum load p that the member can support : A stainless steel tube with an outside diameter of 59 mm and a wall thickness of 5 mm is used as a compression member. If the axial normal stress in the member must be limited to 220 MPa, determine the maximum load P that the member can support.
How long will the generator run on a tankful of fuel : A Bonda portable generator is powering a small travelling fridge (120V) in your RV and consumes 125 watts. The efficiency of the generator's gas motor is 23% and the electrical portion (power head) is more efficient at 91%. If white gas weighs 6.073 ..
Calculate rocket position velocity and accelaration : To calculate a rocket’s position, velocity, and acceleration at different points in time. A rocket, initially at rest on the ground, accelerates straight upward with a constant acceleration of 58.8m/s^2
Determine the time when they pass each other : A motorcycle starts from rest at t = 0 and travels along a straight road with a constant acceleration of 4ft/s^2 until it reaches a speed of 50ft/s . Afterwards it maintains this speed. Also, when t = 0, a car located 8000ft down the road is travelin..
What will the cars maximum acceleration rate be under these : A 3000-lb car is traveling on a paved road with Cd (coefficient of drag) = 0.35, Af (frontal area of the vehicle) = 21ft^2, and p(air density)=0.002378 slugs/ft^3. Its engine is running at 3000rpm and is producing 250ft-lb of torque.
What will be the population in the year 2050 : A very small country has just gained independence in the year 2000, at which time its population was 1,000. The new country has a birth rate of 0.02 yr-1, death rate of 0.004 yr-1, immigration rate of 0.01 yr-1, and emigration rate of 0.005
How many resistors out of a package of 100 would you expect : Water is pumped 9 mi from a reservoir at elevation 100 ft to a second reservoir at elevation 210 ft. The pipeline connecting the reservoirs has a 54-in diameter. It is concrete and has an absolute roughness of 0.003. If the flow is 25 mgd and pumping..
Determine the velocity and position of point : Over a long period, total phosphorus (TP) has been discharged to a lake through sewage and surface water runoff at a rate of 10 tons/day. Measures were then taken to reduce the TP load to 1 ton/day. Assume that TP decays by a first order process with..
Calculate the coefficient of variation and determine : Given a one independent variable linear equation that states cost in $K , and given the following information, calculate the coefficient of variation and determine it's meaning. n=8 E(Y-Y^) =6874 Y=314.375 If we used this equation,

Reviews

Write a Review

Civil Engineering Questions & Answers

  What is the concentration of cod in the effluent

The maximum specific growth rate of the organisms driving this reaction is 5.0 days -1 and the growth rate is 0.54 day-1. The activated sludge tank has a volume of 40 m3 and the flow rate into it is 400 m3/day.

  Determine the viscosity of the fluid at a distance

Two parallel plates are separate at a distance of 2mm by a fluid. If a shearing stress of 150 Pa is developed at the upper plate when it is pulled at a velocity of 1m/s. Determine the viscosity of the fluid.

  Estimate the storage change for this lake during the month

How much extra water does a 21.5 ft, 175-lb concrete canoe displace compared to an ultra-lightweight 38-lb Kevlar canoe of the same size carrying the same load?

  A 200 lb homogeneous gate of 10 ft width and 5 ft long is

a 200 lb homogeneous gate of 10 ft width and 5 ft long is hinged at point a and held in place by 12 ft long brace as

  Defines the product proposal as a 3rd angle

Describes multiple functions of the product with respect to the user and how those functions / features might be used. It gives the reader an excellent sense of context for the product - Contains a high level of visual realism to fully define the p..

  What supported in the weak direction at the one-third points

The member is 24ft long with pinned end supports and is laterally supported in the weak direction at the one-third points of the total column length. Use 50 ksi steel.

  Calculate the maximum shear force v of resisting

If the allowable shear stress is 100 MPa, calculate the maximum shear force V that a W460 X 60 structural steel wide flange is capable of resisting. Use the average web shear approach.

  What percent of the particles does the settling tank capture

The setting velocity of a particle is 0.002 m/s and the overflow rate of a settling tank is 0.008 m/s. (a) what percent of the particles does the settling tank capture. If the particles are flocculated so that thie rsettling rate is 0.05 m/s

  Determine the variation of the peak soil friction angle

This Table gives the standard penetration numbers determined from a sandy soil deposit in the field. Depth (m) 3.0, 4.5, 6.0, 7.5, 9.0, 10.5, 12. Unit weight of soil Kn/M^3

  Determine what are air flow and particulate concentration

Three streams of polluted air are combined prior to treatment in an electrostatic precipitator (ESP). The flow and particulate concentration of each stream are 600 cfm at150 mg/m^3, 700 cfm at 200 mg/m^3, and 500 cfm at 1000 mg/m^3.

  Determine the moment of inertia about ahorizontal axis

By integration, determine the moment ofinertia about a horizontal axis at the channel bottom. Using the parallel axis theorem, determine the moment of inertia about ahorizontal axis through the centroid.

  Determine the required mass of block a so that when it is

Determine the required mass of block A so that when it is released from rest it moves the 5-kg block B a distance of .75m up along the smooth inclined plane in t=2s. Neglect the mass of the pulleys and cords.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd