User Account

All Pages

What types of applications can this circuit be used in

Assignment Help Other Engineering
Reference no: EM131229128

LAB Assignment

MOSFETs

INTRODUCTION

Discuss the basic differences between JFETs and MOSFETs. Why should MOSFETs be handled with special care?

EQUIPMENT

- 1 power supply: 15V
- 2 transistors: MTP10N05E/MC, IRF510
- 1 resistor: 470?
- 1 potentiometer 500kΩ
- 1 diode: red LED
- <List meters used>

PROCEDURE

Using Multisim construct the circuits shown below:

2476_Cricuit.jpg

a. Set the potentiometer to 0% then measure and record VGS, ID, VD.

b. Set the value to 45% and take the three measurements.

c. Increase the potentiometer until the LED turns off, record the readings.

d. Replace the transistor with the IRF510 and repeat steps a) through c).

RESULTS

 

MTP10N05E/MC

IRF510

 

VGS

VD

ID

VGS

VD

ID

0%

 

 

 

 

 

 

45%

 

 

 

 

 

 

LED off

 

 

 

 

 

 

Discuss the results.

What types of applications can this circuit be used in? Explain.

CONCLUSION

What did you learn?

Reference no: EM131229128

Questions Cloud

Identify the flow of events within each use case : Draw a use case diagram for the following dentist office system, but do not bother to identify the flow of events within each use case. Whenever new patients are seen for the first time, they complete a patient information form that asks their nam..
Simple way of detecting common mis-typings of card numbers : Credit card numbers have what is called a check digit. This is a simple way of detecting common mis-typings of card numbers. The algorithm is as follows:
How vital was expert testimony to the case : ow vital was expert testimony to the case? How would you as the prosecutor have prepared the expert witnesses for trial? Could a conviction have been rendered without the fiber evidence? What other evidence did the prosecution present?
Encounter when examining defense perimeters : There are many scenarios one might encounter when examining defense perimeters. These include the single router, defense-in-depth, and demilitarized zone (DMZ) methods. Each has a strategic approach geared specifically toward the environment in wh..
What types of applications can this circuit be used in : What types of applications can this circuit be used in? Explain. Set the value to 45% and take the three measurements. Set the potentiometer to 0% then measure and record VGS, ID, VD.
Develop workplace policy and procedures for sustainability : BSB60215 Advanced Diploma of Business Assignment Task. Develop workplace policy and procedures for sustainability. Develop, implement and evaluate a sustainability process suitable to the workplace at Lonsdale Institute. Complete and provide written ..
Discuss the strengths and weaknesses of financial statements : PRBA007 - Discuss why you are bothered by these trends and offer one or more explanations that may underlie what is actually going on within Flexcom and Despite sluggish sales volume, the company's net income has steadily increased for each of the l..
Define what these groups are trying to accomplish : Although these statements may contain some truth, they very often do not fully define what these groups are trying to accomplish. Without this information, how can the government effectively combat these groups' actions? The reality is that they c..
List the steps taken to arrive at a solution : The table below shows readings for three different cases where the circuit above, was malfunctioning. Find the fault, assuming only one device in each case has a problem. List the steps taken to arrive at a solution.

Reviews

Write a Review

Other Engineering Questions & Answers

  Design an appropriate ventilation system

Design an appropriate ventilation system for production for whole mine through ventilation and develop an appropriate auxiliary ventilation system for stope development

  Differences in ph and condtivitives between water samples

Explain in detail Why there is some differences in pH and condtivitives between water samples?

  Define what is meant by a process in a process model

Define what is meant by a process in a process model. How should the process be named? What information about a process should be stored in the CASE repository?

  Plot the voltage and current for a transmission line

EEGR424 Power Systems. In a distribution network to a  sub transmission customer using a Swan AWG=4  aluminum cable, steel reinforced cable and transmission theory, A) plot the voltage and current for a 250Km transmission line at 25 degrees Celsiu..

  Determine the rate of energy destruction

If the temperatures of the inner and outer surfaces of the bottom of the pan are 104°C and 105°C, respectively, determine the rate of energy destruction within the bottom of the pan during this process, in W. Take T0 = 25°C.

  How much distance must be cleared from the center

what is the station of the PI and how much distance must be cleared from the center of the lane to provide adequate stopping sight distance?

  Determine the effect on the radon daughter concentration

Determine the effect on the radon daughter concentration and describe the methods that can be used to control heat and humidity in an underground mining situation.

  Life cycle of public health partnerships

Explain the life cycle of public health partnerships. Why are collaborative partnerships important? What reasons or issues lead to the termination of partnerships?

  Force with an equivalent force-couple system

A plumber applies a 220-N force to the handle of a wrench as she removes a coupling from the end of a pipe. Knowing that the wrench and the force lie in a vertical plane parallel to the yz plane, replace the force with an equivalent force-couple s..

  Determine the heat transfer

The isentropic turbine efficiency is 87%, and the condenser pressure is 1 lbf/in.2. Determine the heat transfer in the reactor and in the super heater to produce a net power output of 1000 Btu/s.

  Investigate and analyse client and user requirements

Critically think and solve engineering design problems and investigate and analyse client and user requirements, technical briefs - Evaluate design team provision and develop appropriate working methods and Investigate and analyse client and user req..

  Design and detail the tension reinforcement

The L-beam illustrated in Figure is to carry, in addition to its own weight, a dead load g = 25 kN/m and a live load q = 100 kN/m over a simply-supported span of 8 m. Design and detail the tension reinforcement.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd