Reference no: EM131295395

Week 4 mid term

Question 1
Copper is a good conductor.
True
False

Question 2
Doping is a process of adding impurity atoms to an intrinsic crystal to alter its electrical conductivity.
True
False

Question 3
You can quickly check the condition of a diode with an ohmmeter on a high resistance range.
True
False

Question 4
The letter Q is an abbreviation for quiescent, which represents the AC signal is operating between cut-off and saturation points of the transistor.
True
False

Question 5
The half-wave rectifier has a diode in parallel with a load resistor.
True
False

Question 6
In an NPN transistor, the emitter and collector are both n-type materials.
True
False

Question 7
The dc beta is also known as the current gain because a small base current controls a much larger collector current.
True
False

Question 8
The load line is a visual summary of all the possible transistor operating points.
True
False

Question 9
With the switch in the position as shown in Figure 1 below, the LED is on.
Figure 1
True
False

Question 10
A transistor can be tested using an ohmmeter to check back and front resistances of emitter-base, collector-base, and collector-emitter.
True
False

Question 11
Hard saturation refers to any design that makes the saturation current gain approximately:
1
10
100
1000

Question 12
While testing a transistor with an ohmmeter, a high reverse/forward resistance ratio for the emitter-base and base-collector junctions indicates
this transistor is good.
this transistor is open and should be replaced.
this transistor is shorted and should be replaced.
this transistor is a small-signal amplifier.

Question 13
A major advantage of an optocoupler is the:
electrical isolation between input and output circuits.
electrical connection between input and output circuits.
higher gain.
low cost of manufacturing the device.

Question 14
With normal circuit operation, Vout in Figure 2 is ________.
Figure 2
Approximately 0V
115 Vac
20 V
10 V DC

Question 15
If the 115 V ac is removed from the circuit shown in Figure 2, what would be measured at Vout?
Figure 2
approximately 0 V
115 V
20 V
10 V

Question 16
What type transistor connection is shown in Figure 3 below?
Figure 3
common emitter
common collector
common base
emitter follower

Question 17
What is the device that increases a transistor's power rating by reducing the internal heat faster?
heater wire
chassis
grommet
heat sink

Question 18
Another name for diode offset voltage is:
barrier potential
ripple voltage
surge voltage
filtered voltage

Question 19
The second approximation of a silicon diode is basically the:
the diode appears as a switch in series with a barrier potential of 0.7 V

the diode appears as a switch in parallel with a barrier potential of 0.7 V
the diode appears as a barrier potential of 0.4 V
the diode appears as a short circuit

Question 20
What is the most popular and useful semiconductor material?
silver
Copper
Aluminum
Silicon

Question 21
Refer to Figure 4 below.
Figure 4
What is the Peak secondary voltage?
What is the peak-to-peak voltage at the filter point considering non-ideal diode?
For the toolbar, press ALT+F10 (PC) or ALT+FN+F10 (Mac). Content Editor
Use arrow keys to select functions
Bold
Italic
Underline
Font family
Font size
Text Color
Bullet List
Number List
Toggle Spell Checker
Insert/Edit Link
Remove Link
Bold
Italic
Underline
Strikethrough
Format
Font family
Font size
Bullet List
Number List
Text Color
Highlight
Remove Formatting
Cut
Copy
Paste
Find
Undo
Redo
Align Left
Align Center
Align Right
Align Full
Indent
Outdent
Superscript
Subscript
Insert/Edit Link
Remove Link
Direction Left to Right
Direction Right to Left
Line
Horizontal Rule
Insert Nonbreaking Space Character
Toggle Spell Checker
Browse My YouTube Videos
Launch Math Editor
Insert Mashup
Show Nonprinting Characters
Blockquote
Symbol
Emotions
Anchor
Insert/Edit Table
Table Row Properties
Table Cell Properties
Insert Row Before
Insert Row After
Delete Row
Insert Column Before
Insert Column After
Delete Column
Merge Table Cells
Split Merged Table Cells
HTML Code View
Edit CSS Style
Preview
Help
Full Screen

Question 22
For the CE circuit shown in Figure 5 below, draw the dc load line and mark the dc working point on it. Assume Beta=100 and neglect VBE.
Figure 5

Attachment:- Assignment.rar