What type of volcano is olympus mons

Assignment Help Civil Engineering
Reference no: EM13546854

A-Olympus Mons, a 69,000-foot-tall mountain on Mars, is the largest volcano in the solar system. Its circumference at the base is large enough to cover almost the entire state of Colorado. A space probe could safely land at almost any point on the volcano without fear of it toppling over due to a landing on a steep slope. What type of volcano is Olympus Mons?

a. Stratovolcano

b. Cinder cone

c. Caldera

d. Shield

e. Can’t tell from just the information provided

B-The rocks exposed in Boulder Canyon are almost all igneous. The texture of these igneous rocks is phaneritic. By recognizing this texture you can tell the following about the geologic history of Boulder Canyon:

a. An explosive volcanic eruption formed the rocks of Boulder Canyon, meaning that the rocks were likely formed in a caldera

b. The silica content of the Boulder Canyon rocks is high, meaning that the canyon is composed of continental crust

c. The rocks of Boulder Canyon lay far beneath the surface when they formed, meaning that a major episode of erosion occurred since then

d. The rocks of Boulder Canyon must form a dike, because if they formed a sill the texture would be aphanitic instead

Reference no: EM13546854

Questions Cloud

Compute the allowable load on a column with fixed ends : Compute the allowable load on a column with fixed ends if it is 5.45 meters long and made from an S150 x 18.6(S6 x 12.5) beam. The material is ASTM A36 steel. Use the AISC formula.
Compute the critical load when the bar is subjected to an : A rectangular steel bar has cross-sectional dimensions of 12mm by 25mm and is 210 mm long. Assuming that the bar has pinned ends and is made from AISI 1141 OQT 1300 steel, compute the critical load when the bar is subjected to an axial compressive lo..
Need to select a hydraulic pump size and a hydraulic : An Engineer is designing a hydraulic lift with a capacity of 10 tons. The moving parts of this lift weigh 1000 lbf. The lift should raise the load to a height of 6 ft in 20 sec.
Draw the influence line for the shear in panel cd : Draw the influence line for the shear in panel CD of the girder. Determine the maximum negative live shear in panel CD due to a uniform live load of 500 lb/ft action on the top beams.
What type of volcano is olympus mons : A-Olympus Mons, a 69,000-foot-tall mountain on Mars, is the largest volcano in the solar system. Its circumference at the base is large enough to cover almost the entire state of Colorado. A space probe could safely land at almost any point on the vo..
What is the approximate present worth of the 120 mm pipe : The company will use an annual interest rate of 10%. Annual maintenance and pumping costs may be considered to be paid in their entireties at the end of the years in which their costs are incurred.
Series connection of batteries with automatic ups system : Series Connection of Batteries with Automatic UPS System.
What is a solenoid and solenoid magnetic field : What is a Solenoid and Solenoid Magnetic Field ?
How much benzene they can release into river : A company near City X want's to know how much benzene they can release into River Y. City Z is 85.5 miles downstream from City X. City Z doesn't want to have Benzene levels higher than 0.0000015 g/L.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine the deflection at the mid span of a simple

Determine the deflection at the mid span of a simple beam (wood joist) of a row house. The joist is designed as 2x12@16'' for DL = 12psf and LL=40 psf.

  Discuss whether shoe a or shoe b is better for environment

Discuss whether shoe A (leather) or shoe B (synthetic) is better for the environment based on the data in the table below. Is it possible to weight one aspect (air, water, land pollution or solid waste) as being more important than anothe

  What is temperature of the tires of the increase pressure

A motorists inflates the tires of her car to a gauge pressure of 180 kilopascals on a day when the temperature is -8.0 degrees Celsius. When she arrives at her destination, the tire gauge pressure has increased to 245 kilopascals.

  Determine the total vertical stress the pore water pressure

A river 5 m deep flows over a sand deposit. The saturated unit weight of the sand is 18 kN/m^3 and the unit weight of water is 9.8 kN/m^3. At a depth of 5 m below the river bed:

  Plot magnitude of the force exerted on the gate by the brace

A 200lb homogeneous gate of 10ft width and 5ft length is hinged at point A and held in place by 12ft long brace as the bottom of the brace is moved to the right the water level remains at the top of the gate.

  Calculate the minimum set-back distance required

Calculate the minimum set-back distance required for a national highway of 4 lane divided carriageway having circular curve of radius of 350 m & design speed 100 km/hr.

  Compute the magnitude of the force supported by the pin at c

The portable floor crane in the automotive shop is lifting a 420 lb engine. For the position compute the magnitude of the force supported by the pin at C and the oil pressure p against the 2.70 in. diameter piston of the hydraulic cylinder unit AB..

  Thermal conductivities of aluminum and copper

The aluminum end and the copper end are maintained at temperatures of 50°C and 260°C, respectively. The thermal conductivities of aluminum and copper are 205 and 385 W/m · K, respectively. The temperature of the aluminum-copper junction in the rod..

  Determine the maximum external pull of the four gears

Determine the maximum external pull, in each of the four gears, for a tractor with 23-hp, and a max speed of 3.6 mph in 1st gear and a efficiency of 92%. When it is operated over a haul road whose slope is +2.53%.

  What safety factor will be necessary to allow an extraction

A lead-zinc mine is to be developed by a room-and-pillar layout.  The mine is located at a depth of 500ft, the overlying rock has an average specific gravity of 2.56, and the pillar rock wast tested and found to have a

  Determine location of the centroid relative to the channel

A trapezoidal river channel section has a base dimension of 30 feet, a liquid depth of 4 feet, and side slopes of 4 to 1 (horizontal to vertical).

  Determine the placement d of the column at b

The concrete girder supports the two column loads. If the soil pressure under the girder is assumed to be uniform, determine its intensity w and the placement d of the column at B.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd