What must drivers eye height be in van for students claim

Assignment Help Civil Engineering
Reference no: EM13298782

A 1200 ft. equal tangent crest vertical curve is currently designed for 50 mph. A civil engineering student contends that 60 mph is safe in a van because of the higher drivers line of site. If all other design inputs are standard, what must the drivers eye height be in the van for the students claim to be valid?

Reference no: EM13298782

Questions Cloud

Interpret a current social or political issue : How does the Eightfold path help followers to deal with suffering and describe how a Buddhist worldview might interpret a current social or political issue today.
Find by how much is the column compressed : A 4.3-m-tall, 50-cm-diameter concrete column supports a 1.0×105{\rm kg} load. By how much is the column compressed
What is the highest possible design speed for the curve : design a horizontal curve for a two lane road. The road has 12 ft. lanes. Due to expensive excavation, it was determined that a maximum of 34 ft. can be cleared from the roads centerline towards the inside lane to provide for stopping sight distan..
Calculate the radius of the horizontal pipe : Water (? = 1.00E-3 Pa*s) is flowing through a horizontal pipe with a volume flow rate of 0.0149 m3/s. Calculate the radius of the horizontal pipe
What must drivers eye height be in van for students claim : A civil engineering student contends that 60 mph is safe in a van because of the higher drivers line of site. If all other design inputs are standard, what must the drivers eye height be in the van for the students claim to be valid
Explain what is the lowest cyanide concentration : An aqueous solution at 25 °C is 2.28 x 10^-7 M in CuNO3 and 5.03 x 10^-7 M in AgNO3. What is the lowest cyanide concentration at which a precipitate appears
Find the direction of the buoyant force acting on the block : A block of mass M=0.986kg is floating stationary in a beaker of water. A string connected to the bottom of the beaker holds the block in place. find the direction of the buoyant force acting on the block
What is the average degree of consolidation for clay layer : A normally consolidated clay layer is 4 m thick (one way drainage). From the application of a given pressure, the total anticipated primary consolidation settlement will be 80mm. What is the average degree of consolidation for the clay layer.
Calculate the total cross-sectional area of the capillaries : Although the cross-sectional area of a capillary is much smaller than that of the aorta, there are many capillaries, so their total cross-sectional area is much larger. calculate the total cross-sectional area of the capillaries

Reviews

Write a Review

 

Civil Engineering Questions & Answers

  Standard deviation in lines of levels

Lines of levels were run requiring n instrument setups. If the rod reading for each backsight and foresight has a standard deviation δ what is the standard deviation in each of the following level lines?

  Determine what is the present value of the truck

CPM Construction plans to buy a truck for $150,000 and sell it for $15,000 at the end of 5 years. The annual operating cost of the vehicle is $60,000. What is the present value of the truck

  Determine the percentages of gravel-sand-silt and clay

The particle-size characteristics of a soil are given in this table. Draw the particle-size distribution curve. X-axis is Particle Size and Y-axis is Percent Finer Particle Size (mm): 0.425, 0.033, 0.018, 0.01, 0.0062, 0.0035, 0.0018, 0.001.

  Find shear stress on each bolt and bearing stress on the bar

Due to an error, the length L shown was 1.795 m instead of 1.80 m, thus there is a gap of 0.5 cm, which makes it difficult to bolt the bar on the structure. The engineer suggests the bar is heated up by - Delta in order to close the gap.

  Installation of motor on pw criterion

At the end of 15 years, the first motor will have a salvage value of $50 and the second motor will have a salvage value of $100. consider the MARR to be 8%. (note : 1HP=0.7457 kw). Determine which motor should be installed based on the PW criterio..

  Write a report on toxic and hazardous waste

Toxic and Hazardous waste: how are they treated, safety measures, regulations in USA about hazardous waste.

  Force exerted by the hydraulic cylinder

The gate is rectangular with a horizontal width of 2m perpendicular to the paper. For a depth h = 3m of water, calculate the required force exerted by the hydraulic cylinder to keep the gate just closed.

  Determine what is the pond depth above the 5 ft

calculate the depth of water in a stormwater pond resulting from a two hour rainfall event. the rainfall occurs over a 24-acre watershed at an average rate of 1 inch/hour. the runoff coefficient is 0.5.

  Determine what is the effluent bod concentration

An activated sludge tank, 30 x 30 x 200 ft, is designed as a plug-flow reactor, with an influent BOD of 200 mg/L and a flow rate of 1 million gallons per day. a. If BOD removal is first-order reaction, and the rate constant is 2.5 days^-1, what is ..

  Explain some of the benefits of physical models and mock-ups

Describe some of the benefits of physical models and mock-ups. What data are required to measure the following cost-effectiveness, system effectiveness, operational availability, and life-cycle cost?

  What is the maximum step height

An open rectangular channel is 50 feet wide, flowing at a depth of 5 feet, and is carrying 1000 cubic feet per second. What is the maximum step height than can be placed into the flow without disturbing the upstream depth, without acting as a chok..

  Discuss the different environmental companies

Discuss the different agencies, institutes, centers, different environmental companies that are active in UAE.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd