What is the vial radius of curvature

Assignment Help Civil Engineering
Reference no: EM13562655

1.With the bubble centered, a 100-m length sight gives a reading of 1.352 m. After moving the bubble four divisions off center, the reading is 1.410 m. For 2-mm vial divisions, what is (a) the vial radius of curvature in meters and (b) the angle in seconds subtended by one division?

Reference no: EM13562655

Questions Cloud

Determine the modulus of elasticity of concrete by the aci : Determine the Modulus of Elasticity of Concrete by the ACI formula for a concrete cylinder that has a unit weight of 120pcf (1920kg/m^3) and a compressive strength of 3000 psi (21MPa).
How much power is required to overcome aerodynamic drag : A new sports car has a drag coefficient of 0.30 and a frontal area of 21 ft 2 , and is traveling at 110 mi/h.How much power is required to overcome aerodynamic drag if ? = 0.002378 slugs/feet3 ?
What will its length be if a force of 420lbs is applied : Water at 68 degrees f is in a long, rigid cylinder of inside diameter 0.600 in. A plunger applies pressure to the water. If, with zero force, the initial length of the water column is 25.00 in, what will it's length be if a force of 420lbs is applied..
Atrazine is an herbicide widely used for corn and : Atrazine is an herbicide widely used for corn and is a common groundwater pollutant in the corn-producing regions of the United States.  The log Kow for atrazine is 2.65. A typical application rate is 0.25 g/m2.
What is the vial radius of curvature : With the bubble centered, a 100-m length sight gives a reading of 1.352 m. After moving the bubble four divisions off center, the reading is 1.410 m. For 2-mm vial divisions
What is the velocity of an electron that falls through : What is the velocity of an electron that falls through a magnetic field aligned electric potential of volts across an accelertion region that is 10 k long? (neglect collisions and gravity and assume the electron has zero degree pitch-angle (i.s movin..
Determine the direction of the resultant force measured : The driver of a car traveling up a 2% grade at an initial speed of Vo applied the brakes abruptly and the vehicle slid to a complete stop at an average deceleration of 8ft/s^s. Was the pavement wet or dry?
Determine the normal strain in each bar : The two bars shown in the figure are used to support a load P. When unloaded, joint B has coordinates (0, 0). After load P is applied, joint B moves to the coordinate position (0.35 in., -0.60 in.). Assume a = 11 ft, b = 6 ft, and h = 8 ft. Determine..
How much work must be done to move a chair : How much work must be done to move a 3.8 kg chair 6.1 m acrossthe floor at constant velocity if the coefficient of kineticfriction between the chair and the floor is 0.64

Reviews

Write a Review

Civil Engineering Questions & Answers

  Calculate the critical radius and the number of atoms

Calculate the critical radius and the number of atoms in the nucleus of the homogeneous nucleation in GERMANIUM. The latent heat of fusion is 8100 cal per g-mile (atom) and the coefficient of linear expansion is 5.75*10^-6 per K

  By what factor must the length of the current board be

A diving board of uniform cross-section is designed to deflect 6" under the weight of a 150 pound person standing on the end. With the recent trend towards obesity

  Detemine the elevation and stationing of the low point

A horizontal curve on a single lane highway has its pc at station 124+10 and its pi at station 131+40.the curve has a super elevation of 0.06 and its designed for 70 mi/hr.what is the station of the pt" is pending

  Determine the probability that there will be hurricane

A 10-year hurricane is subjected to occur at a given region. Determine the probability that: a) Only one such hurricane occurs within the next 10 years; b) no such hurricane occurs within the next 10 years

  Comparison between steel structures

Comparison between steel structures and aluminium structures, To make a comparison between Eurocode 3 and Eurocode 9 outlining the main differences

  Cantilever mass-less beam

Consider a cantilever mass-less beam subjected to a concentrated mass at the tip of the beam. Assume, length L, flexural stiffness EI, and mass m.

  Determine the tradeoff between the cost and the energy head

Two materials (wrought iron, ks = 0.046 mm, and galvanized iron, ks = 0.15 mm) are being considered for a new pipeline. The expected discharge is 0.15 m3/s. Both the head loss and cost are sought for.

  Determine time required for the bed to complete a full cycle

The velocity of the bed is limited to a maximum value of 150mm/s to the right and 300mm/s to the left; the acceleration is successively equal to 150mm/s^2 to the right, zero 150 mm/s^2 to the left, zero, etc.

  Determine the density and pressure in cgs absolute units

A certain gas has a molecular mass of 40. It is under a pressure of 2.5atm and a temperatature of 25 Degree Celsius. Determine its density and pressure in CGS absolute units.

  What will be the total cost of the material in compacted

Material for an earth filll was available from borrow sites at $6.4 per cubic meter and a void ratio of 0.8. In the compacted state the fill measured 100,000m3 at void ratio of 0.7. what will be the total cost of the material in compacted state?

  Determine what is the change in head across the turbine

A 0.9 efficient Francis turbine produces 200 MW with a speed of 150 rpm. The blade height is 1.0 m, and the inlet radius of the rotor is 7.0 m. The flow exits the turbine in a radial direction.

  What is the probability that the vehicle pulling out will

A vehicle pulls out onto a single lane highway that has a flow rate of 280 veh/h (poisson distributed). The driver of the vehicle does not look for oncoming traffic

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd