What is the temperature of the vapor exiting the valve in c

Assignment Help Civil Engineering
Reference no: EM13304739

Ammonia vapor flows through a valve. It enters the valve at a pressure of 8 bar and a temperature of 120C and after going through a throttling process it exits at a pressure of 3.5 bar. What is the temperature of the vapor exiting the valve in C?

Reference no: EM13304739

Questions Cloud

Determine what is the gas pressure in the tank in bar : Two kg of oxygen at 40C are contained in a 2 m3 closed rigid tank. Assuming that oxygen behaves as an ideal gas under these conditions, what is the gas pressure in the tank in bar.
What does a credit report contain : Money management skills. Use research to report what the professionals say about creating a budget. For example, what monthly expenses will you need to include in the creation of a budget?
Determine the speed of the command module : A space vehicle is traveling at 3570 km/h relative to Earth when the exhausted rocket motor is disengaged, What is the speed (in km/h) of the command module relative to Earth just after the separation
Which set of projects should be accepted : Which set of projects should be accepted, and what is the firm's optimal capital budget?
What is the temperature of the vapor exiting the valve in c : Ammonia vapor flows through a valve. It enters the valve at a pressure of 8 bar and a temperature of 120C and after going through a throttling process it exits at a pressure of 3.5 bar.
Calculate how many turns does this solenoid contain : A current of 7.93 A in a solenoid of length 14.2 cm creates a 0.327-T magnetic field at the center of the solenoid. How many turns does this solenoid contain
Calculate the velocity of air at the entry in ft per second : A compressor pressurizes air from 1 atm to 2.38 atm at steady state. At the entry the air's temperature is 70F, whereas at the exit it has quadrupled (in degrees F). At the entry the air's volumetric flow rate is 17 ft3/s
What was the original temperature of the pan : A 750 g aluminum pan is removed from the stove and plunged into a sink filled with 10.0 liters of water at 20.0 ° C. What was the original temperature of the pan
What force will need to be applied to block downward to hold : A wood cube with 9 inch sides is inserted into water. The specific gravity of wood is 0.60. What force will need to be applied to the block downward to hold the wood cube completely submerged in water

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine the force required to lift the block of stone

Determine the force required to lift the block of stone that weighs 200 lb. The rollers are frictionless and the static coefficient between all other surfaces is 0.3. Neglect the size and weight of the wedges.

  How to determine the head loss caused by the piers

A bridge has cylindrical piers 1 m in diameter and spaced 15 m apart. Downstream of the bridge where the flow disturbance from the piers is no longer present, the flow depth is 2.9 m and the mean velocity is 2.5 m/s.

  What is the difference between factor of safety

what is the difference between factor of safety in rankine & coulomb in overturning, sliding and bearing capasity ?

  What is the astronomic azimuth of the line

The magnetic north azimuth of a line is 128 degrees 27' while the magnetic declination is 3 degrees 30'E. What is the astronomic azimuth of the line (in decimal degrees)?

  Determine the depth that will result upstream during design

The design discharge is 9.5 m^3/sec and the inlet will be submerged but not the outlet. Determine the depth that will result upstream (above the invert) during the design flood event.

  Determine the value of po

Determine the value of Po, as a funciton of H, for these two investment alternatives to be equivalent at an interest rate of i=15% per year.

  What is lowest grade possible for the constant-grade section

A tangent section of highway has a -1.0% grade and ends at station 0+1450and elevation 25m. It must be connected to another section of highway that has a -1% grade and that begins at station 1+345 and elevation 40m.

  Calculate the compressive normal stress in the bar

A stainless steel (304) bar with a cross section of 0.2" x 0.4" is cut to a length of 30" and placed between two immovable walls at a  temperature of 40 degrees F. The operating temperature for the bar is 200 degrees F.

  Convert all quantities to si units then convert it to mph

Assume the plane is flying at an altitude of 32,810 ft (10 km), where the temperature is -8 C and the pressure is 250 mb. The Pitot-static tube measures a piezometric pressure difference corresponding to 1.206 psi. What is the airspeed in both m/s..

  Determine the angle of twist

A beryllium copper wire having diameter of 1-50 mm and length of 40mm is used as a small torsion bar in an instrument. determine what angle of twist would result in the wire when it is stressed to 250 mpa.

  What is the soils unit weight when the degree of saturation

A dry quartz sand has a unit weight of 100 pcf. What is the soil's unit weight when the degree of saturation is 75% if Gs = 2.66

  Allowable shearing stress

The allowable shearing stress is 15 ksi in the steel rod AB and 8 ksi in the brass rod BC. Knowing that the torque of magnitude T=10 kip * in. is applied at A, determine the required diameter of a) rod AB, b) rod BC.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd