User Account

All Pages

What is the smallest particle size that will be removed

Assignment Help Civil Engineering
Reference no: EM13302714

What is the smallest particle size (density 2.65 g/cm3) that will be removed in a horizontal grit chamber 10 m long and 1.0 m deep if the flow rate is 1000 m3/hr? Assume the temperature of the water is 25°C.

Reference no: EM13302714

Questions Cloud

Calculate the density and specific weight of carbon dioxide : calculate the density and specific weight of carbon dioxide at a pressure of 300 kN/m^2 absolute and 60º C
Find the factor by which kinetic energy of ball increases : A ball and bat, approaching one another each with the same speed of 1.1 m/s collide. Find the speed of the ball after the collision. find the factor by which the kinetic energy of the ball increases
How would each of these plans affect earnings per share : How would each of these plans affect earnings per share? (Round your answers to 2 decimal places. Omit the "tiny_mce_markerquot; sign in your response.)
Make a c program that will calculate the gross pay : Write a C program that will calculate the gross pay of a set of employees. For each employee the program should prompt the user to enter the clock number, wage rate, and number of hours as shown below.
What is the smallest particle size that will be removed : What is the smallest particle size (density 2.65 g/cm3) that will be removed in a horizontal grit chamber 10 m long and 1.0 m deep if the flow rate is 1000 m3/hr. Assume the temperature of the water is 25°C.
Obtain the wave number : A wave on a string is described by D(x,t) = (1.2 cm)sin[2 pi (x/(3.9 m) + t/(0.4 s) + 1)], where x is in m and t is in s. What is the wave number
How would friction factor and pressure change be affected : Water at 20ºC flows at a velocity of 2 m/s in a 200-mm diameter horizontal ductile-iron pipe. a) Estimate the friction factor in the pipe, and state whether the pipe is hydraulically smooth or rough
Program revenues-general government-operating grants : General journal for governmental activities at the government-wide level - Program Revenues-General Government-Operating Grants and Contributions
Estimate base cost of each alternative regarding provision : For the Panhandle Medical Practice, I need help with the first question which is estimate the base cost of each alternative regarding the provision of ultrasound services.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Compute the design compressive strength for lrfd

A w14X74 of A992 Steel has a length of 20 feet and fixed ends. Compute the design compressive strength for LRFD and the allowable compressive strength for ASD.

  Explain roman technology and engineering

Roman technology and engineering. Technology and engineering were among Rome's most famous achievements. Describe and explain the importance of Roman technology and engineering

  Prove that the fluid in the pipe will flow from a location

Assume that you have a constant diameter pipe that has no pumps or turbines connected to it.Prove that the fluid in the pipe will flow from a location with high piezometric pressure to one with low piezometric pressure.

  Ehermal conductivity of the radioactive wastes

The outer surface of the tank is cooled by air at 300 K with a heat transfer coefficient of 100 W/m2K. Determine the maximum temperature in the tank. Take the thermal conductivity of the wastes as 2.0 W/mK.

  Determine the manning coefficient of channel roughness

A discharge of 2,200 ft^3/sec flows in a trapezoidal channel at a normal depth of 8.0 ft. The channel has a slope of 0.01, a 12-ft bottom width, and side slopes of 1:1 (H:V). Determine the manning coefficient of channel roughness

  Horizontal axle passing through center

A 75g , 30cm--long rod hangs vertically on a frictionless, horizontal axle passing through its center. A 12g ball of clay traveling horizontally at 2.5m/s hits and sticks to the very bottom tip of the rod.

  Allowable shearing stress

The allowable shearing stress is 15 ksi in the steel rod AB and 8 ksi in the brass rod BC. Knowing that the torque of magnitude T=10 kip * in. is applied at A, determine the required diameter of a) rod AB, b) rod BC.

  Factors of safety against sliding and against overturning

Determine the factors of safety against sliding and against overturning, and also the soil pressure at the heel and toe. Assume hydrostatic uplift varies uniformly from full hydrostatic head at the heel of the dam to zero at the toe. consider 1m l..

  What will be the new level of service

If an additional 11ft lane is added (each direction) and all other factors stay the same, what will be the new level of service?

  What are the proceeds of this sale

What are the proceeds of this sale and if the note was sold at simple discounting conditions instead, at a simple discount rate of 17%, how much would the sellerleceive for the note?

  Strength of a semicrystalline polymer

Briefly explain how each of the following influences the tensile or yield strength of a semicrystalline polymer and why: (a) Molecular weight (b) Degree of crystallinity (c) Deformation by drawing (d) Annealing of an undeformed material

  Determine mans velocity and acceleration at the instant

While the swing bridge is closing with a constant rotation of 0.5 rad/s, a man runs along the roadway such that when d = 10 ft he is running outward from the center at 5ft/s with an acceleration of 2 ft/s^2, both measured relative to the roadway.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd