What is the size and location of the output waist

Assignment Help Electrical Engineering
Reference no: EM13286034

A Gaussian beam has a waist of 1.0 mm located 20.0 cm away from a thin converging lens of focal length 10.0 cm. If the wavelength of the source is 633 nm, what is the size and location of the output waist.

Reference no: EM13286034

Questions Cloud

Write an mips assembly language program to calculate : Write an MIPS assembly language program to calculate (2* ! N ) where ! is the factorial of a given positive integer N using loop.
What is the irr for each of these projects : NPV versus IRR. Framing Hanley, LLC, has identified the following two mutually exclusive projects.
Design a synchronous sequential circuit to control operation : Design a synchronous sequential circuit to control the operation of an automatic coffee machine. A cup of coffee costs 15cents and the machine has two input slots. In one slot Only 10cent coins can be inserted , in the the other only 5cent coins.
Determine the length of wire you must use to wind the coil : Nichrome wire of cross-sectional radius 0.758 mm is to be used in winding a heating coil. find the length of wire you must use to wind the coil
What is the size and location of the output waist : A Gaussian beam has a waist of 1.0 mm located 20.0 cm away from a thin converging lens of focal length 10.0 cm. If the wavelength of the source is 633 nm, what is the size and location of the output waist.
Find the torsion constant of the wire : For the two conducting balls as described in problem 1, when one ball is attached to a torsion balance the wire is twisted by a torsional angle of 1°. find the torsion constant of the wire
Find the approximate magnitude of the electric field : A rod 50 cm long and 1.0 cm in radius carries a 2.0 microC charge distributed uniformly over its length. Find the approximate magnitude of the electric field
Dtermine the resistance values for a voltage divider : Dtermine the resistancevalues for avoltage divider that must meet the following specifications. The currrent drain under the unload condition is nit to exceed 5mA. The soure voltage is to be 10V and 5V . Sketch the citcuit.
Determine the work performed by the gas during the cycle : In a Carnot cycle, the isothermal expansion of an ideal gas takes place at 400K, determine the work performed by the gas during the cycle

Reviews

Write a Review

Electrical Engineering Questions & Answers

  What is torsional constant of hair spring connected to coil

i. The sender sends frames with increasing sequence numbers to the receiver. Only frames received in correct order are accepted by the receiver. ii. The receiver sends a NAK back to the sender when it receives an out-of-sequence frame.

  What is the probability that a tick carries both l and h

Deer ticks can carry both Lyme disease (L) and human granulocytic ehrlichiosis (H). In a study of ticks in the Midwest, it was found that 16% carried L, 10% carried H and 25% that had either L or H carried both.

  How many bits per symbol are required to modulate signal

digital radio link has a bandwidth of 8 kHz and support a transmission of 87 kbps. According to Nyquist how many bits per symbol are required to modulate the signal Remember to use an integer number of bits.

  Minimize the next state equations using karnaugh maps

Design a synchronous circuit that implements a 4-bit decade (modulo-10) counter  (0000,0001, ..., 1001, 0000,...) a. Fill in a transition table (using don't cares for undefined next states).

  Find the value of power gain in db of an amplifier

An amplifier with a voltage gain of +40 dB, an input resistance of 10 kO, and an output resistance of 1 kO is used to drive a 1-kO load. What is the value of Avo Find the value of power gain in dB

  Write a boolean expression in canonical minterm form

1. Write this as a Boolean expression in canonical minterm form 2. Rewrite the expression in canonical maxterm form 3. Write the complement of f in 'little m' notation and as a canonical minterm expression

  Determine whether the system is stable or not

A system has a characteristic equation: q(s) = s3 + 20s2 + 5s + 100 = 0 Determine whether the system is stable using the Routh-Hurwitz criterion. Determine the roots of the characteristic equation.

  Find the impulse response in n domain

The transfer function (TF) of a system is given below. Find its impulse response inn domain. Hint: First multiply the TF by the z-transform of input-or x(z)-or the z-transform of unit impulse. Factor the denominator and then expand.

  What is the characteristic equation of the system

The transfer function of a circuit is given by H(s)= 2s+4/4s^2+2s+2 a. Express the transfer function in a form in which the coefficients of the highest power of s are unity in both numerator and denominator.

  How big will be torque on shaft of motor is efficiency

mutual shifted by 90 degree currents through each of both windings of the single phase A motor are (5.5+1.7) A but RMS voltage of the supply is 220 V. How big will be torque on shaft of the motor is efficiency factor (\eta\) is 0.7

  What is the dopant concentration on the p-type side

A pn-junction is formed in silicon by doping one side with acceptor atoms at concentration Na = 10^19 cm^(-3) and another side with donor atoms at Nd = 10^18 cm^(-3). What is the dopant concentration on the p-type side and on the n-type side

  What is the appropriate range of the symbol duration

Distortion per data symbol is negligible and the time variation during a symbol period is negligible - what is the appropriate range of the symbol duration in this communication system?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd