What is the required press tonnage to perform this operation

Assignment Help Civil Engineering
Reference no: EM131420478

A bearing of simple geometry is to be pressed out of bronze powders, using a compacting pressure of 207 MPa. The outside diameter = 44 mm, the inside diameter = 22 mm, and the length of the bearing = 25 mm. What is the required press tonnage to perform this operation?

Reference no: EM131420478

Questions Cloud

Determine its final porosity : In a certain pressing operation, the metallic powder fed into the open die has a packing factor of 0.5. The pressing operation reduces the powder to 2/3 of its starting volume.
Discuss about the choosing an expert witness : Determine two (2) key factors that legal system professionals could use when selecting an expert witness. Next, discuss one (1) fundamental way that an expert can influence the legal system and analyze whether this is an advantage or a disadvantag..
What is progressivism : What is Progressivism? Would it always fit our modern definition of what is "progressive?" How did progressives preach a "social gospel?" In your opinion, were progressives calling for social reform, or a social revolution (this answer may depend ..
Fault of the united states : Is the negative state of the world today the fault of the United States? or is the positive state of the world to the credit of the United States?
What is the required press tonnage to perform this operation : A bearing of simple geometry is to be pressed out of bronze powders, using a compacting pressure of 207 MPa. The outside diameter = 44 mm, the inside diameter = 22 mm, and the length of the bearing = 25 mm. What is the required press tonnage to pe..
Open position for an accredited record technician : You are the manager of a health information management (medical records) group, and you are interviewing to fill an open position for an Accredited Record Technician (ART). Human resources has referred four candidates to you, all of whom have been de..
Discuss how two laws or regulations apply to the case study : Discuss how two laws or regulations apply to the case study. Discuss how VL Bank will work within the parameters of appropriate legal jurisdiction with specific bodies of law enforcement to resolve the situation
Proper credit and documentation of sources : Your initial answer to the question should be between 250 - 300 words long. Include references and citations where necessary to ensure proper credit and documentation of your sources. You are welcome to include references in addition to the course..
What is the point of total assumption for the seller : The project has finished and the actual cost that the seller incurred was $207,643. What incentive fee does the buyer pay the seller? What is the total contract price (i.e., what the buyer has to pay the seller in total)? What incentive fee does the ..

Reviews

Write a Review

Civil Engineering Questions & Answers

  How to derive the unit hydrogaph by the inverse procedure

Given below are the measured stream flows in cfs from a storm of 6-hour duration on a stream having a drainage area of 185 mi^2. Derive the unit hydrogaph by the inverse procedure. Assume a constant base flow of 550cfs.

  Properties and use of construction materials

You have been asked by your managing director to put forward to present at a young professionals conference organised by the CIOB. You have to submit the following essay to the organisers for final selection.

  Determine the magnitude of the resultant of the two forces

Obstruction due to underground electric lines requires that the x coordinate location of point C must be three feet as shown in the figure, as opposed to 1.5 ft for point B. Determine the magnitude of the resultant of the two forces

  Estimate the test section velocity in miles

An open-circuit wind tunnel draws in sea-level standard air and accelerates it through a contraction into a 1 m-by-1 m test section.

  Determine if the driveway will be affected

A developer wants to provide access to a new building from a driveway placed 1000 ft upstream of a busy intersection.  He is concerned that queues developing during the red phase of the signal at the intersection will block access.  If the speed on t..

  Calculate the magnitude of the electric field in side

A point charge of -2.00μC is locatedin the center of a spherical cavity of radius 6.51cm inside aninsulating spherical charged solid. The charge density in the solid7.34*10^-4 C/m^3.

  Determine the maximum allowable value of p

The compound bar carries the axial forces P and 2P. Find the maximum allowable value of P if the working stresses are 40 ksi for steel and 20 ksi for aluminum, and the total elongation of the bar is not to exceed 0.2 in.

  Compute the allowable load on a column with fixed ends

compute the allowable load on a column with fixed ends if it is 5.45 meters long and made from an S150 x 18.6(S6 x 12.5) beam. The material is ASTM A36 steel. Use the AISC formula.

  Compare the crystalline state in metals and polymers

(a) Compare the crystalline state in metals and polymers. (b) Compare the noncrystalline state as it applies to polymers and ceramic glasses

  Find what will be the percentage change in the volume

An open vat in a food processing plant contains 400L of water at 20 degrees C and atmospheric pressure. If the water is heated to 80 degrees C, what will be the percentage change in its volume? If the vat has a diameter of 3m

  Determine the normal stress and shear stress acting

Determine the normal stress and shear stress acting on the inclined plane AB . Solve the problem using the method of equilibrium described in Sec. 9.1 .

  Calculate number-average molecular weight of random nitrile

Calculate the number-average molecular weight of a random nitrile rubber [poly(acrylonitrile- butadiene) copolymer] in which the fraction of butadiene repeat unit is 0.30

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd