What is the mole fraction of water in the exhaust stream

Assignment Help Mechanical Engineering
Reference no: EM13711752

A mixture of propane and butane is fed into a furnace where it is mixed with air. The furnace exhaust leaves the furnace at 343°C, 780.0 mmHg and contains only N2, O2, CO2, and H2O. The partial pressure of O2 in the exhaust is 51.40 mmHg and the partial pressure of CO2 in the exhaust is 62.40 mmHg.

1) What is the mole fraction of propane in the fuel stream?

2) What is the mole fraction of water in the exhaust stream?

3) What is the dew point temperature of the exhaust gas?

Reference no: EM13711752

Questions Cloud

Determined the flame temperature of the burner : Propane is mixed 20% excess air (propane air mixture is initially at 25 C and 2.0 atm) and combusted at atmospheric pressure. It is assumed that the heat transfer between the chamber and the surroundings is negligible. In addition, you may assume tha..
A credential references : Write ethics reflection paper 6pgs with a credential references. Ethics in business.
Is triple-bottom-line accounting a reasonable approach : 3. Is triple-bottom-line accounting a reasonable approach to encourage businesses to take responsibility for the impact of their actions on social and environmental systems, or does it place an unrealistic burden on businesses to measure what may ..
Determine the mass flow rate of propane : A typical gas stove burner supplies a kettle filled with water at a rate of 15,000 Btu/hr with a flame temperature of 750C. The gas fed to the burner is composed of propane mixed with 10% excess air. The gas feed is initially at -20C and 1 bar and th..
What is the mole fraction of water in the exhaust stream : A mixture of propane and butane is fed into a furnace where it is mixed with air. The furnace exhaust leaves the furnace at 343°C, 780.0 mmHg and contains only N2, O2, CO2, and H2O. The partial pressure of O2 in the exhaust is 51.40 mmHg and the part..
The mole fraction of water vapor in the air : If the weather report says that it is 60°F outside, the barometric pressure is 28.50 in Hg, and the relative humidity is 85.0%, find the following values. The partial pressure of water. The mole fraction of water vapor in the air
Determine the rate of heat transfer in the heat exchanger : A heat exchanger is to heat water (Cp= 4.18 KJ/Kg.C ) from 25 to 60 C at rate of 0.2 kg/s. the heating is to be accomplished by geothermal water ( Cp= 4.31 KJ/Kg.c ) available at 140C at a mass flow rate of 0.3Kg/s. Determine the rate of heat transfe..
Coca-cola blak was introduce to various international market : Coca-Cola Blak was introduced to various international markets including the USA and discontinued in the US market in 2007. In this case you are to analyze a famous firm's product failure and in doing so demonstrate your understanding of a prom..
Determine the temperature at the compressor exit : Air is compressed from 14.7 psia and 60 F to a pressure of 150 psia while being cooled at a rate of 10 Btu/lbm by circulating water through the compressor casing. the volume flow rate of the air at the intel conditions is 5000 ft^3/min, and the power..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Compare the minimum theoretical rate and the actual rate at

at steady state. a power cycle generates 100 mw of electricity while discharging energy by heat transfer at a rate of

  Design problem - piston and flywheel

Design Problem - Piston and Flywheel : Analyze the motion of the crankshaft AB and flywheel for 0 ≤ θ ≤ 4Π (two complete rotations of the crankshaft, or all four cycles, beginning and ending at TDC), for different values of the four design paramete..

  Determine the maximum pressure across a 10 hp pump that

determine the maximum pressure across a 10 hp pump that has an inlet diameter of 1.0 inches and velocity of 10 fps. the

  Whats the maximum acceleration of the car from a standing

a front-wheel-drive car has mass of 680 kg 4 roadwheels of diameter 530 mm wheelbase 2.70 m length 4.22 m and width

  What is the volume of this container

1.49 kilograms of water in a container have pressure of 200 kpa and temperature of 500 celsius. What is the volume of this container? Round to 3 decimal places and v must be in m^3

  Compression ratio and inlet pressure to give maximum imep

Design an SI engine operating on an four-stroke air-standard cycle using stoichiometric gasoline is to have a maximum cylinder pressure of 11,000 kPa at WOT. Inlet pressure can be 100 kPa without supercharging, or it can be as high as 150 kPa with a ..

  The surfaces air temperature is 15 degree c a parcel of air

the atmosphere is stable with a lapse rate of -0.2 degree c100 m. the surfaces air temperature is 15 degree c. a parcel

  The retracting load on a 2 in diameter hydraulic cylinder

the retracting load on a 2 in diameter hydraulic cylinder increases from 10000 lbto 15000 lb. du to the compressibility

  Determine what kind of drive is best and to select suitable

determine what kind of drive is best and to select suitable components .the driven equipment requires 60hp and should

  A reversible heat engine operating a 1500 f source and the

a reversible heat engine operating a 1500 f source and the atmosphere at 0 f produces work to drive a reversible heat

  Calculate the friction loss in the turbine

If the efficiency of the turbine in converting the mechanical energy given up by the fluid to the turbine shaft is 89% (nt = 0.89), calculate the friction loss in the turbine in J/kg.

  The controlled variable in a closed-loop system is a robot

the controlled variable in a closed-loop system is a robot arm. initially it is at 45 degrees then it is commanded to

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd