What is the minimum removal efficiency of the electrodialys

Assignment Help Civil Engineering
Reference no: EM13543421

An electrodialysis is used to treat a stream of 125 m3/d produced water with a salinity of 13,000 mg/L NaCl before the produced water is discharged to the river with the flow rate of 5 million L/d and salinity of 20 mg/L NaCl. The flow rate of the concentrated salt stream exiting the electrodialysis is 20 m3/d. Below the discharge point of the treated produced water is a prime sport fishing spot, and the fishes are intolerant to salt concentrations above 200 mg/L. What is the minimum removal efficiency of the electrodialysis? Assume that the density values of the concentrated salt stream and all of the untreated/ treated produced water streams are identical.

Reference no: EM13543421

Questions Cloud

Find an expression for the flowrate and average velocity : Water flows steadly in an open topped channel of rectangular cross section. The channel width is B and the depth of the water is D. The flow is designed using a rectangular coordinate system whose orgin is at the free surface midway
Calculate its elongation when a load of 300 n is applied : Consider a cylindrical nickel wire 2.0 mm in diameter and 3 x 10^4 mm long. Calculate its elongation when a load of 300 N is applied. Assume that the deformation is totally elastic.
Calculate the super-elevation required for a horizontal : Calculate the super-elevation required for a horizontal curve on a two-lane, two- way highway with 60 mph design speed, and a 1200 ft. radius curve. What is the required length of the spiral curve
Determine the final temperature when valve is opened : An adiabatic piston-cylinder device equipped with a spring maintains the pressure inside at at 300kPa when the volume is 0, and 3000kPa when the volume is 5 m3. The device is connected to a steam line maintained at 1500kPa and 200 C, and the initial ..
What is the minimum removal efficiency of the electrodialys : An electrodialysis is used to treat a stream of 125 m3/d produced water with a salinity of 13,000 mg/L NaCl before the produced water is discharged to the river with the flow rate of 5 million L/d and salinity of 20 mg/L NaCl
Determine the magnitude of the resultant hydro static force : he circular steel plate A is used to seal the opening on the water storage tank. Determine the magnitude of the resultant hydrostatic force that acts on it. Density of water = 1Mg/m^3
Compare those factors that determine the characteristic : Electromagnetic radiation may be treated from the classical or the quantum mechanical perspectives. Briefly compare these two viewpoints.
What will be the effect of heating the lid and jar : For a rubber component that, in its final form is to be vulcanized, should vulcanization be carried out prior or subsequent to the forming operation? Why?
How to determine span of the subject beam which theoretical : Again assuming d=14in, determine, or at least show exactly how to determine, the portion (length) of span of the subject beam which theoretically would require no shear reinforcement.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Problem regarding helium balloons

To float a 160 pound man using helium balloons (assume 0.52 cubic feet per inflated balloon). How many balloons would it take? Assume density of air is 1.29 kg/cubic meter and the density of helium is 0.179 kg/cubic meter.

  Three different materials designated a b and c are tested

three different materials designated a b and c are tested in tension using test specimens having diameters of 0.755 in.

  What would be the resultant force on the plate

A 40-mm-diameter jet has a velocity of 25 m/s. If this jet were to strike a large flat plate normally, what would be the resultant force on the plate?

  How will velocity and pressure distribution change from case

Consider the flow of a gas between two parallel plates. If there were an increase in temperature due to heat transfer along the flow direction, the gas density would decrease. Assume the viscosity is unaffected.

  How fast was the car traveling before applying the brakes

The vehicle was estimated to hit the light pole at 30 mph. The skid was 650 feet long. How fast was the car traveling before applying the brakes

  What should be the minimal diameter of the above tank

For an elevated storage tank , if the minimum allowable pressure = 300 kPa, Height of pipe system at low-pressure service location = 6 m, and head loss from tank to service location: average daily conditions = 11 m

  Determine the magnitude of force f2 and the angle

Two ropes are attached to the eye bracket. The resultant force R of the two forces equals 1000-lb and the line of action is directed along the x-axis. if the magnitude of force F1 is 250-lb, determine the magnitude of force F2 and the angle

  Determine effective annual interest rate for a nominal rate

Determine the effective annual interest rate for a nominal rate of 8% per year, in which is compounded quarterly.

  What is the change in centimeters

The evaporation rate from the surface of a 3,650-acre lake is 100 acre-ft/day. Estimate the depth change in the lake in feet during a 1-year period if the net inflow to the lake is 25 cfs. Is the depth increasing or decreasing? What is the change in ..

  What is the minimum size inch wall thickness column acme

ACME supplies prepackaged steel framed and sheathed storage buildings in kit form. The standard column used is a steel hollow round tube with a wall thickness of 0.4 inches fixed at both ends.

  Calculate speed of the shockwave foamed by the bottleneck

When stationary, vehicles are spaced at average distance headway of 6 m. It may be assumed that there is a linear relationship between speed and density. When the traffic flow approaching the roadworks is 3500 vehicles per hour

  Calculate the amount of each phase present in a 1-kg alumina

Calculate the amount of each phase present in a 1-kg alumina refractory with composition 70 mol % Al2O3- 30 mol% SiO2 at 2,000 C , 1,900 C and 1,800 C

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd