What is the minimum number of filters required by plant

Assignment Help Civil Engineering
Reference no: EM13313789

A conventional water treatment plant treats 2.40m^3*s^-1 of river water. The filters in the plant are 8.0x8.0m surface area and operate on the following schedule. A filter is cleaned once in each 24-hr period, and a backwash rate is 10.0 L*m^-2*s^-1 fora period of 8 min. it takes an additional 8 min to drain the filter and break up the media with air injection. of the total fitler cylce time of 24 hours, 15 mins is used for rinsing the filter after backwashing. During production, water is applied to the filter at a rate of 5.50 L*m^-2*s^-1

(a) What is the filter efficiency?

(b) What is the minimum number of filters required by plant?

Reference no: EM13313789

Questions Cloud

Policies around the use of mobile technologies : Your report should be longer than 3 pages or 1,500 words (whichever is greater) and should contain relevant tables, calculations, a ranked list of threats and conclusions that may assist in formulating policies around the use of mobile technologi..
What is the time between consecutive pulse beats : Suppose Galileo's pulse rate was 68 beats per minute. What is the time between consecutive pulse beats
Depict lewis structures to ecompounds exhibit resonance : Draw Lewis structures to determine which of the following compounds exhibit resonance. Enter the letters corresponding to all those compounds which exhibit resonance
How large of an area would one need to cover with solar cell : Given that the average power plant produces 667 MW of electricity per year, there are 492 coal plants in the US, and a solar constant of 1.361 KW/m^2, how large of an area would one need to cover with solar cells to replace our dependence on coal ..
What is the minimum number of filters required by plant : The filters in the plant are 8.0x8.0m surface area and operate on the following schedule. A filter is cleaned once in each 24-hr period, and a backwash rate is 10.0 L*m^-2*s^-1 fora period of 8 min.
What would be temp rise of water as it leaves the collector : A 4 X 8-ft solar collector has water circulating through it at the rate of 1.0 gallon per minute (gpm) while exposed to sunlight with intensity 300 Btu/ft2-hr. Fifty percent of that sunlight is captured by the collector and heats the water flowing..
Review should show evidence of understanding of the topic : An Investigation of Weak Form of the Efficient Market Hypothesis in the Nigerian Market - review should show evidence of understanding of the topic and some wider reading.
What flow rate does the filter handle during production : A rapid sand filter has a loading rate of 8.00 m/h, surface dimension of 10m x 8m, an effective filtration rate of 7.70 m/h, and a production efficiency of 96 percent.
Determine all reactions and draw shear and moment diagrams : Analyze the frame by moment distribution. Determine all reactions and draw the shear and moment diagrams, locating points of inflection and labeling max and min shear and moment values.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Design a single angle strut connected to a gusset plate

Design a single angle strut connected to a gusset plate to carry 180k n factored load. The length of the strut between center to center intersection is 3m.

  Estimate the undrained shear strength of clay

Plot variation with depth from the top to Point C for σ' v and σ h when the soil is at rest and Estimate the undrained shear strength (c u ) of clay. (Assume the shear strengths to be 200 kPa and 2 kPa at Liquidity Index (IL) values of 0 and 1, res..

  Minimizing the tension tab

What should TAC , TAB and the acute angle ? between TAB and the vertical to minimize the tension TAB ? Take o and W = 1,000 N. Hint: Consider various possible force triangles and decide on inspection how to minimize TAB.

  Determine what is the force in the wire and beam

The 5-m long cantilever beam using a W410 x 67 standard wide flange section has a distributed load of 1200 N/m placed on it. It is also supported by a cable at B, of length 2 m with a 7 mm2 cross sectional area. What is the force in the wire

  Explain how to calculate the mass flowrate in methane

Assuming the resulting hole acts like an isentropic converging nozzle with a throat diameter of 0.08 cm, calculate the mass flowrate in kg/s of methane that initially escapes from the tank.

  Determine a dollar amount on december 31st-2011

determine a dollar amount on December 31st , 2011 FOR $1000 equal payments made at the end of each of the previous 7 years including the current year. use an effective interest rate of 10% compounded annually.

  Design temperature and residence time have been established

The oven exhaust gases are available at 250 F. Assume that the design temperature and residence time have been established as 1300 F and 0.6 sec, respectively. The type of burner used in the process requires outside air at a moass ratio of 12:1

  Is the noise level of area 1 greater than 60 decibels

Office workers complain that the noise level in their office Area 1 is greater than that in the company's other office Area 2. Six measurements are made on different days in each area, with the following results

  How many short tons of coal are required by plant per year

Assume that the energy contained in coal is about 10,000 Btu/lbm. An electrical power plant burning coal has an output capacity of 1200 MW and the plant converts about 30% of the input energy to electricity.

  Compute the difference in design curve lenghts for designs

The curve is to be redesigned for a 70 mph design speed in the year of 2025. Vehicle braking technology has advanced so that the recommended design deceleration rate is 25% greater that the 2011 value used to develop

  Explain about how big is the hole in the water pipe

A water main springs a leak and the geyser is estimated to be 20 feet in height. It is also estimated that about 300 gallons per minute is leaking based on flow into gutter. About how big is the hole in the water pipe

  Calculate q-w change in u and h for each processes

Cooling at constant pressure followed by heating at constant volume. Calculate Q, W, change in U, and change in H for each of these processes, and sketch the paths of all processes on a single PV diagram.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd