What is the minimum flow rate

Assignment Help Electrical Engineering
Reference no: EM131392798

Figure 52 shows a valve that is operated by a worm gear and motor. Each turn of the worm gear moves the stem by 0.18 cm, and the total range of stem travel is 4.0 cm. The worm gear motor has three states: A TTL high to the up terminal causes rotation at 15 rpm that moves the valve stem up, a TTL high to the down terminal causes rotation to reverse, moving the valve stem down (closing the valve), and with TTL low to both terminals the motor is off. The valve body is equal percentage with a rangeability of 20 and a maximum flow of 0.6 m3/min.

a. How many rotations of the worm gear are required for the full stem travel?

b. How long does it take to move the stem over the full range of travel? What is the minimum flow rate?

c. What is the stem position for flow at 90% of the maximum?

603_Fig 9.jpg

Reference no: EM131392798

Questions Cloud

Explain what the authors main conclusion : In a well-written paragraph, explain what the author's main conclusion, and describe the principle arguments he uses to come to support that conclusion. Then evaluate whether the author has made good arguments in support of her conclusion. The c..
Describe five components and principles of coso framework : Describe the five components and 17 principles of the COSO Framework. Review your company's "Management's Annual Report on Internal Control over Financial Reporting" and "Report of Independent Registered Public Accounting Firm".
Find the fastest time for valve to move from closed to open : If the maximum input pulse rate to the motor is 250 steps per second, find the fastest time for the valve to move from closed to open.
Identify an accounting fraud that was reported in the news : Identify an accounting fraud that was reported in the news within the last 20 years. Prepare a report on the fraud. 1. Make sure your report is properly formatted with a title page, executive summary, section headers, bibliography etc.
What is the minimum flow rate : How many rotations of the worm gear are required for the full stem travel?- How long does it take to move the stem over the full range of travel? What is the minimum flow rate?
Evaluate tax authority and choose which ones take precedence : Evaluate tax authorities and choose which ones take precedence if they conflict. Conclusion and analysis: detailed review and evaluation of sources and how they apply to current situation.
What impact would a balanced-budget amendment : According to the movie Generation Zero, what are some of the root causes that lead up to the 2008 economic crash in the United States? According to Keynesian economics, what impact would a balanced-budget amendment to our constitution have on our nat..
Activate the up or down terminals of the motor : Design a system so that comparators are used to activate the up or down terminals of the motor and drive the stem to the correct position required by the current.
Calculate the effective mass and effective spring constant : A mass of m = 2.5 and a spring with k=42 are attached to one end of a lever at a radius of 4. Calculate the effective mass and effective spring constant at a radius of 12 on the same lever. (Use any unit system.)

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Determine which tunnel allows more modes to propagate

A recent study has been carried out concerning radio propagation in railway tunnels. In this study, two railway tunnels of rectangular cross section are considered. Tunnel 1 has transverse dimensions of width a = 8 m

  Draw all possible wiring arrangements for the load connected

Thre identical impedances are connected to a 3 phase, 415 V, 50Hz Y connected supply, the load draws 21kW at a power factor of 0.82 lagging. Draw all possible wiring arrangements for the load connected to the Y-connected supply.

  Determine the induced emf if a short in the rheostate

The resistance of the shunt field winding and the resistance setting of the shunt field rheostat of a separately excited generator are 10.26 ohm and 14.23 ohm respectively. The field circuit is connected to a 120-V DC source.

  Calculate the generated emf

A shunt generator supplies a current of 85 A at a terminal p.d. of 380 V. Calculate the generated emf if the armature and field resistances are 0.4 Ω. and 95 Ω respectively.

  Calculate the power dissipated in the resistor and the power

Measurements taken on various resistors are shown below. For each, calculate the power dissipated in the resistor and the power rating necessary for safe operation using standard components with power ratings of 1/8 W, 1/4 W, 1/2 W, 1 W, or 2 W

  Find vc in terms of the arbitrary constants c1 and c2

Consider an RLC circuit with R = 5 Ohms, L= ½ H, C= 2/9 F and input voltage e(t) = exp(-t/2)a. Starting from KVL show that the DE for the voltage across R is given by: v'' + 10 v' + 9 v = -5 exp(-0.5 t) b. Find vc in terms of the arbitrary constants ..

  Calculate the current per line

A 3Φ transformer delivers 120 kVA to a 3Φ load from a 2400 V line-to-line source at unity power factor.- Calculate the current per line?

  Does this meet the ssa requirement for an existing system

These other components were mostly off the shelf, but they had never been integrated into a system before. Does this meet the SSA requirement for an existing system?

  Explain how long will the cassette operate at normal power

The four alkaline battery cells store a total of 200 watt-seconds of energy. If the cassette player is drawing a constant 10mA from the battery pack, how long will the cassette operate at normal power

  Sketch a cmos sram cell and describe its operation

Sketch a CMOS SRAM cell and describe its operation. - Discuss any advantages and disadvantages of this design. - Describe how the cell is addressed.

  Determine the counter torque and the power input

A permanent magnet generator has Kt = 0:02Nm/A . The terminal voltage is six volts. It is spinning at 2500 rpm. It is connected to a load with a resistance of 30W. Determine the counter torque and the power input.

  Find transfer function between motor voltage and pressure

The fluid travels through a conduit of negligible resistance; an accumulator is included to smooth out the pulsations of the pump. A hydraulic load (modeled by a fluid resistance R) is connected between a pipe and a reservoir (assumed at zero pres..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd