Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
Biomass is increasingly used as a fuel to produce power and heat. A sugarcane-? processing mill is powered by a biomass power plant with 140 MW of electricity and with 60 MW of heat in the form of steam for sugar extraction from the cane. An unknown number of MW of heat is released by the power plant's cooling towers into the atmosphere. If the power plant's thermal efficiency is 45% (a) What heat input in MW does the power plant get from the combustion of biomass; (b) How many MW of heat are released by the power plant into the atmosphere; (c) If each ton of biomass releases 9 million kJ of heat upon combustion, how many tons of biomass annually does the plant consume for its operation; (d) If electricity is worth 11 cents per kW.h, what is the market value of the plant's electricity annually?
A consolidated-drained triaxial shear test on a normally consolidated clay yielded a drained friction angle of 28 degrees. If the confining pressure during the test was 15 psi, what was the major principal stress at failure.
Truck B has an 8000-lb single axle and a 43,000-lb tandem axle. On a flexible pavement with a 3-inch hot-mix asphalt (HMA) wearing surface, a 6-inch soil-cement base, and an 8-inch crushed stone subbase, which truck will cause more pavement damage
A steel bar of length 30 inches and circular cross section whose diameter varies linearly from 0.50 inches at one end to 0.75 inches at the other is subjected to an axial tensile force of 4.5 kip. Find the change in length of the bar.
A stainless steel tube with an outside diameter of 65 mm and a wall thickness of 5 mm is used as a compression member. If the axial normal stress in the member must be limited to 180 MPa, determine the maximum load P that the member can support.
A solution of HOCl is prepared in water by adding 15 mg HOCl to a volumetric flask, and adding water to the 1.0 L mark. The final pH is measured to be 7.0. What are the concentrations of HOCl and OCl
A 40 oF breeze of 10 miles per hour blows over the top of a round open-top water cooling tank which has a bulk temperature of 100 oF. What is the rate of energy in kW that enters into the air
The inflow to a small reservoir during a storm may be described by the equations Q=1000(1-e^-kt) where Q= flow in cfs k= runoff rate = 1.0 per hour t = time in hours The outflow through the dam gates is held constant at 800 cfs.
water flows from a lake as is shown in fig. p8.40 at a rate of 4.0 cfs. is the device inside the building a pump or a turbine? Explain and determine the horsepower of the device. neglect all minor losses and assume the friction factor is .025
Calculate expected error L if a theodolite has direct angular accuracy of 10" and a distance of 1500m was measured.
The motor in the unit runs at 300 rpm and produces an unbalanced force of 60 lb at this speed. Neglect weight of the beams and assume 1% viscous deflection in the system; for steel E=30,000 ksi.
A single-scoop ice cream cone is a composite body made from a single scoop of ice cream placed into a cone. Assume that the scoop of ice cream is a sphere with radius r=1.45in that is placed into a 4.00in tall cone.
A stream with a flow of 22 mgd contains 180 mg/L of sodium cyanide in the form of NaCN. Chlorine can be added to destroy the NaCN waste according to the reaction shown below. Find the theoretical minimum amount of chlorine required (in lb/day).
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd