Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
A sightseeing tourist submarine is constructed as shown. The portals along the side can be assumed to be essentially flat, vertical and 1 meter in diameter. Assume a specific weight of seawater of 10,000 N/m3.
a) If the submarine operates at a depth of 75 meters (to the center of the side portals), what is the hydrostatic force on one of the side portals, in KPa?
b) In relation to the center of a side portal, where is the center of pressure located, in cm?
c) Due to the presence of both upper and lower ballast tanks, both the submarine's weight and center of gravity can be adjusted. It can also be buoyantly analyzed as having a rectangular cross section 4m wide and 6m tall, and a length of 18.6 m. Assume the submarine is submerged halfway (3 meters) into the ocean, (so the tourists can see dolphins both swimming and jumping). Also assume the center of gravity must remain above the center of buoyancy. Where does the center of gravity need to be located in relation to the bottom of the submarine so it remains buoyantly stable with a metacentric height of +0.2m?
Find the steel area required for beam which has b = 10 in. and d = 17.5 in. to carry a factored load moment of 1,600 in-kips.
How do you propose to do this at the above treatment plant and estimate the head loss both immediately after backwash and 10 hours later, if the same water is applied at a rate of 2 L/s.m 2 .
The trapezoidal channel has a slope of .004. The sides of the canal are sealed with a plastic membrane, which is protected by a 1 ft thick layer of 1 in diameter gravel. The bottom is a 6 in slab of rough concrete.
An overflow spillway 1,600 feet long is designed to pass 120,000 ft3/s of water. A 1:20 scale model of the cross section of the structure is built in the laboratory. It is assumed that the flow is two dimensional so only a 1-foot section
Create a primary function that uses a function handle with a nested function to compute the minimum of the function 20x2-200x+12 over the range 0
An afterburner has been selected to destroy 99.9% of the ethane (CH3-CH3)in a gas (mostly air) stream . if the residue time is 0.8 seconds and the pressure is 1.1 atmospheres in the after burner,
The flywheel of a prototype car engine is under test. The angular position of the flywheel is given by x = (3.0rad/s3)t3 and the diameter of the flywheel is 36cm.
If the atmospheric pressure is 14.20 psia and a gage attached to a tank reads 12.5 inHg vacuum, what is the absolute pressure within the tank
Calculate the stopping sight distance over the crest of a 1,500 ft vertical curve with a plus grade of 4.4percent and a minus grade of 2.3 percent.
How we can find the applicaition of internal force in civil? mean an appication for the internal force in the civil
Calculate the super-elevation required for a horizontal curve on a two-lane, two- way highway with 60 mph design speed, and a 1200 ft. radius curve. What is the required length of the spiral curve
A solid steel shaft with an outside diameter of 65 mm is subjected to a pure torque of 7,000 N-m. The shear modulus of the steel is G=80 GPa. Determine a. 1 The maximum shear stress in the shaft
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd