User Account

All Pages

What is the frequency resolution-df for the analysis

Assignment Help Electrical Engineering
Reference no: EM13231047

An engineer decides to take 600 samples at sampling frequency 9000Hz. A Fast Fourier Transform (fft) program was applied to obtain the frequency spectrum of the signal. What is the frequency resolution,df, for this analysis?

Reference no: EM13231047

Questions Cloud

What size capacitor should be placed in parallel : A Y-connected load has an impedance of 25+j12 ohms in each phase. It is desired to raise the load power factor to .95 lagging. (a) What size capacitor should be placed in parallel with each phase impedance if frequence = 60 Hz
Explain zinc metal is produced by the reaction of the oxide : Zinc metal is produced by the reaction of its oxide with carbon monoxide at high temperature. The equlibrium constant for the equation
Determine the frequency response function of the low-pass : design a 4th order Butterworth band-pass filter, using a low-pass filter followed by a high-pass filter, to extract the 1200Hz and 1500Hz components from the signal x(t) a. Determine the cut-off frequencies of the low-pass and the high-pass filters..
Compute the work done in joules by the reaction : Calculate the work done in joules by the reaction when 0.35 g of Na reacts with water to form hydrogen gas at 5°C and 2.5 atm. 2 Na(s) + 2 H2O(l) 2 NaOH(aq) + H2(g)
What is the frequency resolution-df for the analysis : An engineer decides to take 600 samples at sampling frequency 9000Hz. A Fast Fourier Transform (fft) program was applied to obtain the frequency spectrum of the signal. What is the frequency resolution,df, for the analysis
Describe the lysine and glutamic acid : An individual contains asomatic mutation that changes a codon for lysine (Lys) into a codonfor glutamic acid (Glu)
Find f on side bc and find f on side ab : A rectangular loop of wire in free space joints point A(1,01,) to point B(3,0,1) to point C(3,0,4) to point D(1,0,4) to point A. The wire carries a current of 6mA, flowing the az direction from B to C. A filamentary curent of 15A flows
Describe a dbms and its functions updated dbms technology : Describe a DBMS and its functions. Name some of the popular DBMS software? You should search the Internet for the updated DBMS technology.
What is the footprint of the entire focal plane array : the SABER instrument aboard the TIMED satellite orbits the earth in a sun-synchronous polar orbit 625 Km above the earth. each of the 10 SABER focal plan detectors is 0.14mm high by 2.0mm wide. the focal plane array is 4.882*4.882mm in size

Reviews

Write a Review

Electrical Engineering Questions & Answers

  What factors are moving wireless nics

Discuss whether this is still true today, and what factors are moving wireless NICs into a more dominant role, if any.

  Explain problem on complex power

Problem on complex power, An electric load operates at 240 volts. The load absorbs an average power of 8Kw at a lagging power factor of 0.8.

  Calculate the leading kvars the syncrhonous motor

A 277/480V three phase wye system has the following load: M1- Induction Motor, 50hp, n=0.91, PF= 0.89 at full load. M2- Induction motor, 25hp, n=0.9, PF= 0.9 at full load. R- Heater Load, PF=1 M- A synchronous motor to drive a second 25hp load.

  Design a low-pass filter with a cutoff frequency

A) Design a low-pass filter with a cutoff frequency of 12 kHz. Use 0.15 uF capacitor and an appropriate resistor. B) Sketch and label the circuit. C) What is the gain of the filter at a frequency of 20 kHz Give your answer both as ratio (Vout/Vin) an..

  Explain single phase circuit

Single Phase Circuit, A resistor and a capacitor are connected in series across a 150 V a.c supply. When the frequency is 40 Hz the current is 5 A

  Find the maximum signal energy and design a demodulator

Suppose we transmitted 5 cos wct for logic one and 15 cos wct for logic zero. Find the maximum signal energy. Design a demodulator and show the detection criterion for the output of the demodulator. Finally, find the bit error-rate.

  Find the total circuit impeadance and current source

Find the associated answers for: total circuit impeadance (Zt), Current source (RMS), Vc (RMS) w/ power factor, Vr (RMS), all in complex form/ rectangular form. Remember each question has to be done three times, one for each frequency.

  Find the ratio of the effective density of states

n the conduction band of a semiconductor, it has a lower valley at the center of the Bril- louin zone, and six upper valleys at the zone boundary along [100]. If the effective mass for the lower valley is 0.1m0 and that for the upper valleys

  Identify the noise magnitudes and corresponding frequencies

Suppose you are working for an aircraft company on a positioning control system that controls the position of the landing for their aircraft. This positioning system requires a feedback signal from a position sensor.

  Define circuit analysis

Bode plots were introduced in my second circuit analysis class, but I really didn't think it was important because it looked like an outdated tool no longer in use.

  Plot the magnitude response

Plot the magnitude response (in dB) and the impulse response of the designed filter using MatLab.

  Calculate in polar form the sequence components

Calculate in polar form the sequence components of unbalanced line­to-neutral voltages and calculate in polar form the phase currents corresponding to the sequence components

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd