What is the force ecienccy of the actuator

Assignment Help Mechanical Engineering
Reference no: EM13824806

A cylinder with an area ratio of 0.2 and a bore diameter of 7.5 cm steadily extends a 13.3 kN load. If the cap-side pressure is 4 MPa and the rod-side pressure is 250 kPa, what is the force ecienccy of the actuator?

 

 

Reference no: EM13824806

Questions Cloud

The ball is kicked from point a with the initial velocity : The ball is kicked from point A with the initial velocity vA=10m/s. Determine the range R, and the speed when the ball strikes the ground
Quality control for reducing defects in products : Quality Control For Reducing Defects In Products
Calculate exit velocity if the velocity at entry : An ideal duct carries water (incompressible fluid) from a height of 10m to 20m. The pressures at the entry and exit points are at 1000 Pa and 2000 Pa respectively. Calculate exit velocity if the velocity at entry is 10 m/s.
The cylinder to keep the load stationary : A dynamic compression force,F = 3.5 + 3.5cos (45t) kN is applied to the rod of an ideal cylinder with a bore diameter of 8.4 cm (take note that the force is in kN) (a) Assuming the rod-side of the cylinder is at atmospheric pressure, what gauge press..
What is the force ecienccy of the actuator : A cylinder with an area ratio of 0.2 and a bore diameter of 7.5 cm steadily extends a 13.3 kN load. If the cap-side pressure is 4 MPa and the rod-side pressure is 250 kPa, what is the force ecienccy of the actuator?
Discusses about preparing performance report for a project : Prepare a performance report for the Humphrey Catalog project. This problem belongs to Accounting and it discusses about preparing performance report for a project
What signals are involved in the initiation of its functions : What is it? Where is it from? What is its role in the immune system? What signals are involved in the initiation of its functions?
What is the tension needed to pull a rubber : What is the tension needed to pull a rubber by a distannce z= 10nm at 25 c? Number of individual chains in the rubber, N=1000, bond vector length b=2 Angstrom.Please give your answer in pico Newton - pN
Problem regarding implement the shareholders resolution : Central Property Pty Ltd owns certain property. It is approached by Land Ltd which offers to buy the property at a good price in the current market conditions.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the isentropic efficiency of the compressor

Air is compressed by an adiabatic compressor from 95 kPa and 27°C to 600 kPa and 277°C. Assuming variable specific heats and neglecting the changes in kinetic and potential energies, determine (a) the isentropic efficiency of the compressor and (b) t..

  The ammonia is then cooled until its pressure drops to 10

a constant-volume tank contains 10 lbm of ammonia initially at 30 lbfin2 and 80degf 539.67degr. the ammonia is then

  The tank is heated until its pressure is 100 psia what is a

13 lbm of air inside a rigid tank contains is initially at 100of and 40 psia. the tank is heated until its pressure is

  The upper half of the container holds steam of density

a transparent rigid sealed container has a volume of 10m3. the upper half of the container holds steam of density 5kgm3

  How much electrical work is done to the water in the tank

An electric 50 L hot water tank is initially full and has a temperature of 90 degrees C. Water is drawn from the tank at a rate of 0.08 kg/s. The shower is used for 10 minutes (cold and hot water are mixed). After the shower the water in the tank is ..

  What is the force exerted by the atmosphere downward on the

a pressure vessel of radius 11.0 in is filled with a gas at a pressure of 550.0 psi gauge. the top of the vessel is

  Determine athe fundamental frequency in hz contained in the

consider the signal yt24sin3pit3cos3pit with t in units of seconds. determine athe fundamental frequency in hz

  Does the client–user–designer model still apply

Suppose you are working for a start-up company that is designing a very new and innovative product. Does the client–user–designer model still apply? Who is your client in this case? Since you don’t have any customers yet, who are the users and how ca..

  Determine the power input to the compressor

Refrigerant 22 enters an insulated compressor operating at steady state as saturated vapor at - 16oC with a mass flow rate of 1.5 kg/s. Refrigerant exits at 7 bar, 70oC. Changes in KE and PE from inlet to exit can be ignored.

  A long solenoid has a diameter of 120 cm when a current i

a long solenoid has a diameter of 12.0 cm. when a current i exists in its windings a uniform magnetic field b 27.0 mt

  How should the company hire and train its new employees so

a cheese firm produces two types of cheese swiss cheese and sharp cheese. the firm has 60 experienced workers and would

  What is the gage pressure of the air inside the piston what

consider the arrangement described in problem 1. a cable attached to the 100 lbm piston exerts a 200 lb force upward on

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd