User Account

All Pages

The cylinder to keep the load stationary

Assignment Help Mechanical Engineering
Reference no: EM13824807

A dynamic compression force,F = 3.5 + 3.5cos (45t) kN is applied to the rod of an ideal cylinder with a bore diameter of 8.4 cm (take note that the force is in kN) (a) Assuming the rod-side of the cylinder is at atmospheric pressure, what gauge pressure, P, must be applied to the cap-side of the cylinder to keep the load stationary?

 

 

Reference no: EM13824807

Questions Cloud

Describe a method to determine the cellular immune response : Describe and discuss a method to determine the cellular immune response to an infectious agent in an individual. Discuss in general how a response to an infectious agent is determined.
The ball is kicked from point a with the initial velocity : The ball is kicked from point A with the initial velocity vA=10m/s. Determine the range R, and the speed when the ball strikes the ground
Quality control for reducing defects in products : Quality Control For Reducing Defects In Products
Calculate exit velocity if the velocity at entry : An ideal duct carries water (incompressible fluid) from a height of 10m to 20m. The pressures at the entry and exit points are at 1000 Pa and 2000 Pa respectively. Calculate exit velocity if the velocity at entry is 10 m/s.
The cylinder to keep the load stationary : A dynamic compression force,F = 3.5 + 3.5cos (45t) kN is applied to the rod of an ideal cylinder with a bore diameter of 8.4 cm (take note that the force is in kN) (a) Assuming the rod-side of the cylinder is at atmospheric pressure, what gauge press..
What is the force ecienccy of the actuator : A cylinder with an area ratio of 0.2 and a bore diameter of 7.5 cm steadily extends a 13.3 kN load. If the cap-side pressure is 4 MPa and the rod-side pressure is 250 kPa, what is the force ecienccy of the actuator?
Discusses about preparing performance report for a project : Prepare a performance report for the Humphrey Catalog project. This problem belongs to Accounting and it discusses about preparing performance report for a project
What signals are involved in the initiation of its functions : What is it? Where is it from? What is its role in the immune system? What signals are involved in the initiation of its functions?
What is the tension needed to pull a rubber : What is the tension needed to pull a rubber by a distannce z= 10nm at 25 c? Number of individual chains in the rubber, N=1000, bond vector length b=2 Angstrom.Please give your answer in pico Newton - pN

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  A metal has an atomic radius

A metal has an atomic radius of 0.125 nm, an atomic weight of 58.69 g/mol and a density of 8.9 g/cm3. Determine whether it has a BCC or an FCC crystal structure

  Determine the reduction in the exit temperature of the

the compression stages in the axial compressor of the industrial gas turbine are close coupled making intercooling very

  The acceleration of a particle is defined by the relation

the acceleration of a particle is defined by the relation a25-3x2 where a is expressed in ms2 and x in meters. the

  The masses of the bar and the disk are 5 kg and 10 kg

the masses of the bar and the disk are 5 kg and 10 kg respectively. the coefficient of kinetic frictionnbspbetween the

  Velocity and radius of curvature

Strategy formulation presupposes a set of objectives and goals.

  Find the initial pressure and mass of the system

Water in the pictured piston cylinder assembly has an initial quality of 10%. The piston cylinder is 20 cm in width and the piston is initially 40 cm high. Heat is added until the temperature of the steam reaches 500°C. While heat is being added the ..

  Temperature transducer outputs

A temperature transducer outputs 4 mA of current for 150oF and 20 mA current for temperature of 1oF, then find out Output current value for temperature of 90oF? If the temperature is 70oF, then what is the output current?

  Consider a system which is initially an ice cube 1 meter on

liquid water at 0degc weighs 9810 nm3 and ice at the same temperature weighs 8992 nm3. consider a system which is

  Explain mean effective pressure of a diesel engine

Volumetric Compression Ration and Mean Effective Pressure of a Diesel Engine, A diesel engine has air before compression at 280 K and 85 Kpa. The highest temperature is 2219 K and the highest pressure is 6 MPa.

  If t and p are to remain the same is there any way the

six chemical species are present in significant amounts in a light-ends petroleum fractionation system methane ethane

  Determine the initial temperature of the air in the cylinder

Air (assumed to be an ideal gas) is contained in a piston-cylinder assembly at an initial state of 1 bar with a volume of 1 m3. The mass of air contained in the cylinder is 1 kg. During any expansion or compression of the air, the pressure remains co..

  At what distance downstream of the leading edge that

a thin plate 6 ft long and 3 ft wide is submerged and held stationary in a stream of water t 60 degree f that has a

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd