Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
Question 1: One of your fellow Energy Engineers comments that the flue gas leaving the natural gas-fired boiler that you are designing should be at a high temperature because of dew point. Your boss asks you to examine that argument by performing some calculations.
The natural gas boiler that you are designing uses a gas with a composition of CH4-95% and C2H6 - 4% and other inert gases 1%. You have a coal fired facility next door and they use a coal with the following analysis C-73.4% H-4.3%, S-1.1%, N-1.3%. The fuel's proximate analysis is given as follows: Moisture 6.8%, Ash-8.6%, FC- 65.4 and VM 19.2%. The HHV of the Fuel is 13,380 BTUs/lb. The air that is used is ambient at 78 F and 40% relative humidity. This plant is designed to use 22% exc ess air.
Evaluate both cases and show to your boss with calculations whether the dew point is different? If so by how much? And what is the impact?
Question 2:
If 90% of the sulfur dioxide produced has to be captured from the coal fired power plant in problem 1 (500 MW Thermal) by using lime (CaO). What is the flow rate of the CaCO3 that would be required if CaO is produced by calcining CaCO3? The efficiency of sulfur capture is 65%.
block diagram system performance and responses1. simplify the above block diagram and determine the closed diagram
Determine the dimensions (x4, x1 to x3 are fixed due to construction requirements) of the cantilever retaining wall that satisfy the required factors of safety against overturning, direct sliding and bearing capacity. The parameters are summarized..
Reevaluate the separation using the same total amount of solvent in a counter-current cascade. How much improvement in separation is produced?
Water enters a pump steadily at 100 kPa at a rate of 35 L/s and leaves at 800 kPa. The flow velocities at the inlet and the exit are the same, but the pump exit where the discharge pressure is measured is 6.1 m above the inlet section. The minimum..
question 1case study discussiona the it strategy at nestleacute is almost entirely dictated by the business strategy of
A tin can has a total volume of 1300cm3 and a mass of 160 g. How many grams of lead shot of density 11.4 g/cm3 couldit carry without sinking in water?
Water at 50°F and 50 psia is heated in a chamber by mixing it with saturated water vapor at 50 psia. If both streams enter the mixing chamber at the same mass flow rate, determine the temperature and the quality of the exiting stream.
what is the pressure drop across the pipe? what is the shear stress exerted on the pipe boundary? what is the shear velocity? what is the darcy friction factor?
Calculate the molar composition of this gas on both a wet and a dry basis and the ratio (mol H2O/mol dry gas).
The measured lift and drag coefficients for each rotor were about 10 and 4, respectively. If the ship is moored and subjected to a crosswind of 25 ft/s, as in Fig, what will the wind force parallel and normal to the ship centerline be? Estimate th..
An aqueous solution of potassium hydroxide is fed at a rate of 875 kg/h to an evaporative crystallizer operating at 10°C, producing crystals of KOH·2H2O. A 5 g aliquot of the feed solution is titrated to neutrality with 22.4 mL of 0.85 molar H2SO4..
Explain how one heat treatment process and two other treatment processes affect the structure, properties and behaviour of the parent material
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd