What is the evaporation rate of water from the plate

Assignment Help Mechanical Engineering
Reference no: EM131337768

Dry air at 32°C flows over a wetted plate of length 200 mm and width 1 m (case A). An embedded electrical heater supplies 432 W and the surface temperature is 27°C.

1687_b1c0ba2d-c78f-43fb-b786-be1b031f8f2f.png

(a) What is the evaporation rate of water from the plate (kg/h)?

(b) After a long period of operation, all the water is evaporated from the plate and its surface is dry (case B). For the same free stream conditions and the same heater power as case A, estimate the temperature of the plate, Ts.

Reference no: EM131337768

Questions Cloud

Identify one or more internal control deficiencies : Use your experience or research, identify one or more internal control deficiencies in any of the processes in a firm. You can also search the internet to identify an internal control deficiency in a company subject to Sarbanes Oxley Act.
What are the major effects of logging activity in indonesia : What are the major effects of logging activity in Indonesia?How can the rainforests be protected yet Indonesia gain economic benefit from this great natural resource?
Position of manager-recruitment and selection : The HR department of your organization is adding a new position of manager, recruitment and selection. This position is expected to bring the R&S functions up to "best practices" or state of the art" status.
Explain the significance of confidentiality : Explain the significance of confidentiality in ethical psychological practice, as it applies to the case above. Explain how your feelings, beliefs, attitudes, and cultural perspectives might influence how you conceptualize this case
What is the evaporation rate of water from the plate : After a long period of operation, all the water is evaporated from the plate and its surface is dry (case B). For the same free stream conditions and the same heater power as case A, estimate the temperature of the plate, Ts.
Identify a real world current event : Identify a real world current event to which a method/procedure/model reviewed that week can be applied.discuss the benefits, limitations and challenges associated with applying it, and describe a minimum of one alternative method/procedure/model tha..
Determine the value of simulation training : How do we as HRM professionals objectively determine the "value" of simulation training? Then, discuss the problems of simulation training/development that should be taken into consideration by human resource professionals. Finally, make a recomme..
Explain the larger reciprocal relationship : Explain the larger reciprocal relationship between human creative expression and the culture in which it was created using the insights you gained from studying your artifact
Sample action plan that identify major educational goals : Write a sample action plan that identifies major educational goals, time management plans for meeting those goals, and the benefits to meeting your goals successfully.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  What is the rate of flow of cooling water through the

consider an ideal steam cycle that combines the reheat cycle and the generative cycle. the net power output of the

  Determine the change in the rate at which the following

pressurized water pin 10 bar tin 110 deg c enters the bottom of an l 10-m-long vertical tube of diameter d 100 mm

  Determine 1 the energy flow rate of the oil at the inlet 2

for the following calculations take g 9.8ms2 and pwater1000kgm31. assuming there are both a pressure gage and a

  Determine internal pressure required to initiate yielding

A thin-walled cylindrical pressure vessel is capped at the end and is subjected to an internal pressure (p). The inside diameter of the vessel is 6 ft and the wall thickness is 1.5 inch. The vessel is made of steel with tensile yield strength and com..

  Calculate the maximum tensile stress smax

Determine the orientation of the neutral axis and calculate the maximum tensile stress σmax if b = 80 mm, h = 140 mm, L= 1.75 m, α = 22.5°, and q = 7.5 kN/m. P

  How would you calculate the sensible heat, the latent heat

How would you calculate the sensible heat, the latent heat, and determine the latent heat of vaporization of the water vapor in this air stream as the air is cooled from 170 F to 48 F?

  A circular shaft of 120-mm diameter is subjected to end

a circular shaft of 120-mm diameter is subjected to end loads p 45 kn m 4 kn.m and t 11.2 kn.m. what is the factor

  Actual thermal conductivity of the carbon nanotube

Physicists have determined the theoretical value of the thermal conductivity of a carbon nanotube to be kcn,T = 5000 W/m · K. (a) Assuming the actual thermal conductivity of the carbon nanotube is the same as its theoretical value, find the thermal..

  Calculate the minimum diameter of pipe

A compressor delivers 300 l s-1 of free air into a pipe at a pressure of 6 bar gauge. Using the pressure drop formula: Pressure drop = 800lQ2/Rd5.31 Calculate the minimum diameter of pipe if the pressure drop in a system is to be limited to 0.3 bar ..

  Determine the maximum load that can be applied for the

a plate 50 mm wide and 15 mm thick is loaded in tension. the plate is made from steel with yield strength of 1500 mpa

  Find all propagating modes that can be used

Find all propagating modes that can be used at the given wavelength. The waveguide is air filled.

  Valance structures of sodium and fluorine atoms

Sodium Fluoride (NaF) exhibits ionic bonding due to the valance structures of sodium (Na)and fluorine(F) atoms.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd