What is the elevation of point n

Assignment Help Civil Engineering
Reference no: EM13545650

A transit is setup over a point M on the ground with the transverse axis of the transit 4.9 ft. above that point.

A leveling rod is held vertically on another point N. When a sight is taken on the rod, the telescope is inclined so that the horizontal cross line of the transit intersects the rod at a reading of 4.9 ft.

The observed reading on the vertical limb of the transit is +10° 13’, but is found that there is an index error of +3’.

If the inclined straight-line distance from point M to point N is 154.82 ft. and the elevation of point M is 118.5 ft. What is the elevation of point N ?

Reference no: EM13545650

Questions Cloud

Sketch how you will place the bars and calculate : Concrete cover on both sides. Sketch how you will place the bars and calculate the location of the effective depth. Place as many bars in the lower layers as possible.
Determine for each case the ration of the total energy : Consider two cases: (1) a constant wind velocity that is twice the mean wind velocity and operating half the time; and (2) a constant wind velocity that is three times the mean wind velocity operating one-third of the time. At all other times, the wi..
Design a one way slab to support a uniform live load : Design a one way slab to support a uniform live load of 300 psf. The beam is simply supported with a span of 20 ft. Use a reinforcement ration ( Ps) of 0.008 Use f'c=3000 psi and fy=60000 psi.
The angle measured counterclockwise between line ab and : The true azimuth of line AB is 193 degrees 20'. The angle measured counterclockwise between line AB and another line AC is 205 degrees 10'. The true azimuth of line AC is:
What is the elevation of point n : A leveling rod is held vertically on another point N. When a sight is taken on the rod, the telescope is inclined so that the horizontal cross line of the transit intersects the rod at a reading of 4.9 ft.
What was the difference in elevation between the two points : A rod was held on point B and the telescope is inclined so that the horizontal cross line of the transit intersects the rod at the 5.2 ft mark.If the reading on the vertical limb of the transit was +25° 19’, what was the difference in elevation betwe..
What is the diameter of the ball : A child at a park finds a ball floating in a freshwater pond (temperature 30 degree C). The child swims to the ball and, with an incredible amount of dexterity, balances himself on the ball
Explain how this change in fluid will affect the rate : A centrifugal pump is used to pump Vodka (S.G. 0.8) at a rate of 20 gallons per minute to the top of a 30 foot tall tank. The owner wants to use the same pump to pump orange juice (S.G. 1.1). Explain how this change in fluid will affect:
Which compressor should he buy and why : A diver is planning to salvage a Spanish galleon located in 200 feet of water. He plans to use a diving suit that will be supplied with air from a hose (assume this to be amply sized) connected to a compressor that he will locate in his boat on the s..

Reviews

Write a Review

Civil Engineering Questions & Answers

  Specify and construct the foundations for the new building

The subsoil at the site is a thick layer of soft alluvial river silts and sands, the bearing capacity of the silt has been found to be in the region of 80 kN/m2. There is a high ground water table present.

  Determine from curve the maximum flow rate

Determine from curve (a) critical depth (b) the maximum flow rate (c) the flow rate at a depth of 2.4 m and (d) the depths at which flow rate of 28.3 m^3/s may exist and the flow conditions at these depths.

  Influencing the allowable bearing pressure

What are the two principle factors influencing the allowable bearing pressure in the design of a specific footing- Are both of these factors equally important? Are both factors likely to be equally relevant for different soils types

  How many kilowatt-hours of electricity would be saved

Suppose the utility encourages its customers to replace their 75-W incandescents with 18-W compact fluorescent lamps (CFL) that produce the same amount of light. Over the 10,000-hr lifetime of a single CFL,

  What is min sight distance that should be provided on road

f the design speed of a multi-lane highway is 60 mph, what is the minimum sight distance that should be provided on the road if (a) the road is horizontal and (b) the road has a maximum grade of 5 percent

  What is the drawdown halfway between well a and well b

They each completely penetrate a homogeneous, confined aquifer, and pump at exactly the same rate, 5m^3/day. Prior to pumping, the piezometric head was 30m, the same as the thickness of the aquifer.

  What is the largest number of phases that can coexist

Considering both temperature and pressure to be variables, what is the largest number of phases that can coexist at equilibrium in a binary alloy

  Determine equation of elastic curve for the cantilever beam

For the loading sown, use double integration method to determine: the equation of the elastic curve for the cantilever beam, the deflection at the free end and the slope at the free end.

  Estimate the particle removal efficiency

How do you propose to do this at the above treatment plant and estimate the head loss both immediately after backwash and 10 hours later, if the same water is applied at a rate of 2 L/s.m 2 .

  Determine at which of the two points the elevation is higher

At point 2, the velocity and pressure are 14 ft/s and 23 psi. Determine at which of these two points the elevation is higher. Calculate the height difference. (Assume the sp ecific gravity of butane is 0.6 and that the butane is at a temperature o..

  Determine in the rate of carbon 14 hat is the age

In dating using radiocarbon, the amount of C^14 remaining at the time of measurement is expresed as a percentage of modern carbon. For example that the 30% modern carbon, N/No would be 0.3

  Determine the force p that will cause the bar

the rigid bar abcd is supported by a pin at B and restrained by identical steel bars at C and D, each of area 250mm^2. if the temperature is increased by 80C, determine the force P that will cause the bar at c to be stress-free.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd