What is the difference between working stress approach

Assignment Help Civil Engineering
Reference no: EM13542289

1.What are the functions of different components of a typical expansion joint?

2.What are the functions of grout inside tendon ducts?

3.What are the three major types of reinforcement used in prestressing?

4.What is the difference between working stress approach and limit state approach?

Reference no: EM13542289

Questions Cloud

For finding the elevation of point c the azimuth angle from : For finding the elevation of point C the Azimuth Angle from poit A to C is measured as 76deg ?15'00". The height of the instrument during this measurement was 1.60m
How temperature and pressure interact with other limitation : A nuclear power plant produces heat through fission of uranium which is used to create high pressure steam. The steam expands through a turbine to a low pressure in order to produce work which drives a generator to produce electric power.
What is the work done in terms of the system : What is the work done in terms of the system?
Case study-omarama mountain lodge : Case Study: Omarama Mountain Lodge
What is the difference between working stress approach : What is the difference between working stress approach and limit state approach?
How many moles of solid ba : How many moles of solid Ba(N03)2 should be added to 300ml of 0.20 MFE(N03)2 to increase the concentration of the N03 ion to 1.0M. can you please show steps
A sample of neon is compressed from a volume of 65.0 : A sample of neon is compressed from a volume of 65.0 L to a volume of 13.0 L by an external pressure of 12.0 bar at constant temperature. The neon gains 17.4 kJ of heat. Calculate ?U for the neon gas.
Determine the pressure in a 0.34l balloon : 1) Determine the pressure in a 0.34L balloon if the temperature is 35(celcius) and the balloon contains 0.0233 mol of an ideal gas
Case study - cost reduction : To achieve the best in your assessment and improve your level of mastery of the subject learning outcomes, review both the assessment and subject mastery level rubrics in this document.

Reviews

Write a Review

Civil Engineering Questions & Answers

  What is the optimal life of the forklift in years

Due to the intended service use, the forklift's market value drops 20% of its prior year's value in Years 1 and 2 and then declines by 15% until Year 10 when it will have a scrap/market value of $1000.

  Determine the normal depth yo and critical depth yc

A 1 m diameter unfinished concrete pipe (n = 0.015) has a slope of So = 0.001 and conveys water at Q = 0.5 m3/s. Find the normal depth yo and critical depth yc.

  Determine the horizontal and vertical components of reaction

Determine the horizontal and vertical components of reaction at the supports. Neglect the thickness of the beam

  Compute the range in h corresponding to range in pressure

Compute the height (h) of the water tank above theground surface to provide a static pressure of 75 psi. Compute the pressure at a point in a building that is 40 feet abovethe ground surface.

  Determine what is the rolling resistance of the road

A CAT 834H (rubber tires, high pressure), specs found, is pulled up a road whose slope is +3.0% at a uniform speed. If the average tension in the towing cable is 6,060 lb, what is the rolling resistance of the road

  Determine what is the minumum allowable pipe diamter

The mass flow rate of steam into a steam turbine is 5 kg/s . The turbine has a heat loss of 5 kj/s. if the velocity of the refrigerant is to be limited to 2 m/s, what is the minumum allowable pipe diamter

  Determine the weight of the gate per meter of length

The homogeneous gate shown consists of one quarter of a circular cylinder and is used to maintain a water depth of 4m. That is, when the water depth exceeds 4m, the gate opens slightly and lets the water flow under it. Determine the weight of the gat..

  How many days are required for the concentration to reach

The degradation constant is 0.2 1/d. If the initial concentration is 100 mg/L, how many days are required for the concentration to reach 0.14 mg/L

  Determine the distance that the piston is displaced

a vertical 12-cm diameter piston-cylinder device contains an ideal gas at the ambient conditions of 1 bar and 24 degrees C. Initially, the inner face of the piston is 20 cmfrom the base of the cylinder.

  Determine the density of the air in a laboratory

Some experiments are being conducted in a laboratory in which theair temperature is 26o C and the atmosphericpressure is 14.6 psia. Determine the density of the air.Express your answers in slugs/ft3 andkg/m3.

  Determine what should the velocity for the model be

The prototype and model will both be in air, if the prototype has a velocity of 500 ft/s and a diameter of 30 ft, what should the velocity for the model be if the model diameter is 2 ft

  Design solution that would increase sustainability of water

Stormwater controls are typically designed by civil engineers. Stormwater is collected in pipes below the ground and routed to nearby surface water.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd